background image

RAWS-P Remote Automated Weather Station 

3.6  Barometric Pressure  

The barometric pressure sensor is mounted to the back plate inside the RAWS 
environmental enclosure.

  

3.7  Fuel Moisture and Fuel Temperature  

The fuel moisture and fuel temperature sensor should be left outside at the field 
site continually exposed to the same conditions as forest fuels.  The fuel 
moisture and fuel temperature dowel rods absorb and desorb moisture from its 
surroundings.  Install the probes horizontally on the mounting stake and face 
the sensors south (northern hemisphere) above a representative forest floor duff 
layer.  Place the sensor away from foot traffic areas. 

4.  Sensor Wiring and Troubleshooting 

4.1  Air Temperature and Relative Humidity 

4.1.1  General Description, Air Temperature and Relative Humidity (part 

#HMP45C-LQ) 

The Vaisala Air Temperature and Relative Humidity Sensor (part #HMP45C-
LQ)

 

contains a Platinum Resistance Temperature detector (PRT) probe and a 

Vaisala HUMICAP® 180 capacitive relative humidity probe.  The probe 
output for each sensor is a voltage.  

4.1.2  Wiring, Air Temperature and Relative Humidity (part #HMP45C-LQ) 

The temp/RH sensor is connected to the RAWS connector panel “TEMP/RH” 
connector COLOR CODED ORANGE.  This sensor is internally wired from 
the RAWS connector panel to the CR1000 datalogger.   

Connector Panel “TEMP/RH” connector COLOR CODED ORANGE 

Connector Pin A  Temp Hi 

to CR1000  1L 

Connector Pin B  Sensor excitation 

to CR1000  EX1 

Connector Pin C  Sensor signal Lo/AG  to CR1000  AG 
Connector Pin D  Power ground 

to CR1000  Ground 

Connector Pin E  RH signal 

to CR1000  1H 

Connector Pin F  SW_12V 

to CR1000  SW_12V 

4.1.3  Troubleshooting, Air Temperature and Relative Humidity (part 

#HMP45C-LQ) 

Check the sensor cable.  Disconnect the connector and look for damaged pins.  
Verify that the sensor body is connected to the sensor head.  Under the filter 
assembly, verify the sensors are connected but not touching.  Try connecting a 
substitute sensor.  Obtain a Return Material Authorization (RMA) number 
before returning this sensor to Campbell Scientific for repair. 

Consult the HMP45C-L manual for more information. 

NOTE 

Summary of Contents for RAWS-P



































Reviews: