Campbell OBS501 Operator'S Manual Download

Page: 18 / 66

OBS501 Smart Turbidity Meter with ClearSensor

Technology

7.1 Default Settings

The OBS501 is configured at the factory with the default settings shown in
TABLE

7-1

. For most applications, the default settings are used.

TABLE 7-1. Factory Settings

SDI-12/Analog

SDI-12

SDI-12 Address

RS-232 Baud Rate

9600

Turbidity Units

Temperature Units

Celsius

7.2 Device Configuration Utility

Device Configuration Utility

(

DevConfig

) is used to change settings, set up the

analog sensor, enter RS-232 commands, and update the operating system.

Use the OBS501 test cable to connect the OBS501 to a computer running

DevConfig

. The red wire is connected to a 12 Vdc power supply and the black

to ground. The datalogger power supply is a good choice to use for the power
supply.

DevConfig

software is shipped on the Campbell Scientific

ResourceDVD included with the OBS501.

The OBS501 is supported in

DevConfig

version 1.16 or higher.

NOTE

Summary of Contents for OBS501



































































Search results

Summary of Contents for OBS501

Reviews:

Related manuals for OBS501

Brands by name

Popular brands

Campbell OBS501, Operator'S Manual

Search results

Summary of Contents for OBS501

Reviews:

Related manuals for OBS501

Brands by name

Popular brands