manualshive.com logo in svg

Campbell OBS-5+, Operator'S Manual

Share
Download
Campbell OBS-5+ Operator'S Manual Download Page 15

OBS-5+ System 

6.  Operation 

6.1  Instrument Setup 

6.1.1  Mounting Suggestions 

Maximum depth for the OBS-5+ is limited by the installed 
pressure sensor.  If the maximum depths are exceeded, 
the pressure sensor will rupture and the housing will flood. 

CAUTION 

The depth limits are listed in TABLE 6-1.   

TABLE 6-1.  Working and Maximum Depths 

Pressure Sensor  Working Depth  Maximum Depth 

5 Bar 

0 to 50 meters 

75 meters 

10 Bar 

0 to 100 meters 

150 meters 

20 Bar 

0 to 200 meters 

300 meters 

(1 Bar = 10 dBar 

≅

 10 meters of fresh water)  

 

The following precautions should be followed to ensure the unit can function 
properly and is not lost or damaged.  

•

 

Always orient the unit so that the OBS-5+ sensor “looks” into water clear 
of reflective surfaces. 

•

 

Pad the endcaps that contact metal with electrical tape, neoprene, or 
expanded polyethylene tubes. 

•

 

Never mount the instrument by its endcaps or attach anything to them.  
This could a cause a leak. 

6.1.2  Surveys 

The OBS-5+ will usually be towed with a cable harness for surveys.  The serial 
cable can tow the OBS-5+ without a depressor weight or vane as long as the 
connector is strain relieved.  Strain relief can be provided by attaching the 
cable to the stainless steel housing (FIGURE 4-1) with a cable grip and a 
length of 3 mm (1/8 in) wire rope.  Install a cable clamp with a 0.5 m wire rope 
to the serial cable, and clamp the wire rope to the pressure housing with two 
stainless steel hose clamps, providing a small loop of slack cable to absorb 
towing forces.  The unit can be powered with an external battery, as shown on 
FIGURE 6-1, and the serial output can be transmitted by either RS-232 or  
RS-485 protocols.  The latter protocol is recommended for cable lengths 
greater than 25 m.  An RS-485/232 serial converter is provided with each unit. 
An RS-232 to USB converter is an available option. 

7 

Summary of Contents for OBS-5+





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands