Campbell Hausfeld SB3232, Operating Instructions Manual

Page: 3 / 24

6-Sp
Manual de Instrucciones
Modelo SB3232
3
General Safety
Information
(Continued)
●
Always assume the tool contains
fasteners. Respect the tool as a
working implement; no horseplay.
Always keep others at a safe dis-
tance from the work area in case of
accidental discharge of fasteners.
Do not point the tool toward your-
self or anyone whether it contains
fasteners or not. Accidental trigger-
ing of the tool could result in death
or serious personal injury.
●
Do not drive a fas-
tener on top of
other fasteners.
The fastener could
glance and cause
death or a serious
puncture wound.
●
Do not operate
or allow anyone
else to operate
the tool if any
warnings or
warning labels
are not legible. Warnings or warning
labels are located on the tool maga-
zine and body.
●
Do not drop or throw the tool.
Dropping or throwing the tool can
result in damage that will make the
tool unusable or unsafe. If the tool
has been dropped or thrown, exam-
ine the tool closely for bent, cracked
or broken parts and air leaks. STOP
and repair before using or serious
injury could occur.
Caution indicates
a potentially haz-
ardous situation which, if not avoided,
MAY result in minor or moderate
injury.
●
Do not make any modifications to the
tool without first obtaining written
!
CAUTION
Standard B19.3-1991; Safety
Standard for Compressors for
Process Industries. Contact your air
compressor manufacturer for
information.
Operating The Tool
LUBRICATION
This tool requires lubrication before
using the tool for the first time and
before each use. If an inline oiler is
used, manual lubrication through the
air inlet is not required on a daily basis.
The work surface
can become dam-
aged by excessive lubrication. Proper
lubrication is the owner’s responsibil-
ity. Failure to lubricate the tool proper-
ly will dramatically shorten the life of
the tool and void the warranty.
1. Disconnect the
air supply from
the tool to add
lubricant.
2. Turn the tool so the
air inlet is facing up.
Place 4-5 drops of 30
W non-detergent oil
into air inlet. Do not
use detergent oils,
oil additives, or air tool oils. Air tool
oils contain solvents which will dam-
age the tool's internal components.
NOTICE
approval from Campbell Hausfeld. Do
not use the tool if any shields or
guards are removed or altered. Do
not use the tool as a hammer.
Personal injury or tool
damage may occur.
●
Avoid long extended periods of
work with the tool. Stop using the
tool if you feel pain in hands or
arms.
●
Always check that the Work Contact
Element (WCE)
is operating
properly. A fas-
tener could acci-
dentally be dri-
ven if the WCE
is not working
properly.
Personal injury
may occur (See "Checking the Work
Contact Element" Section).
●
Disconnect air supply and release
tension from the pusher before
attempting to clear jams because
tools can be ejected from the front
of the tool. Personal injury may
occur.
Notice indicates
important infor-
mation, that if not followed, MAY
cause damage to equipment.
●
Avoid using the tool when the mag-
azine is empty. Accelerated wear on
the tool may occur.
●
Clean and check all air supply hoses
and fittings before connecting the
tool to an air supply. Replace any
damaged or worn hoses or fittings.
Tool performance or durability may
be reduced.
●
Air compressors providing air to the
tool should follow the requirements
established by the American
National Standards Institute
NOTICE
Model SB3232
Operating Instructions
www.chpower.com
O I L
!
WARNING
Recommended Hookup
Quick
Plug
Quick
Coupler
Air
Hose
Quick Plug
(Optional)
Quick
Coupler
(Optional)
Oiler
Regulator
Filter
OIL OIL
Calibre Clavos por Clavos por
Modelo # Longitud
del cuerpo
Acabado Cabeza Unión
línea Caja
FB001600 15,9mm (5/8”) Calibre 18 Galvanizado De puntilla/Café Adhesivo 100 5000
FB002000 19,1mm (3/4”) Calibre 18 Galvanizado De puntilla/Café Adhesivo 100 5000
FB002500 25,4mm (1”) Calibre 18 Galvanizado De puntilla/Café Adhesivo 100 5000
FB003000 31,8mm (1
1
⁄
4
”) Calibre 18 Galvanizado De puntilla/Café Adhesivo 100 5000
Clavos
Estos clavos para acabado de Campbell Hausfeld los puede comprar en su tienda más cercana. Si necesita ayuda para encontrar
un artículo, comuníquese al 1-800-543-6400. Los clavos de Campbell Hausfeld cumplen o exceden el estándar ASTM F1667
Información de intercambio
Los clavos usados con Campbell Hausfeld SB3232 2 en 1 Tool también se pueden usar con las clavadoras : Bostitch T31-1, T29-
30, BT-35, Duofast BB4440, Hitachi NT45A , Paslode 2138-F18 , Porter Cable BN125, BN200, Sears 18309, y Senco SLP20, LS2,
LS5.
Grapas
Estas grapas para acabado de Campbell Hausfeld los puede comprar en su tienda más cercana. Si necesita ayuda para encon-
trar un artículo, comuníquese al 1-800-543-6400. Las grapas de Campbell Hausfeld cumplen o exceden las especificaciones
Federales FF-N-105B.
Información de intercambio
Las grapas usadas con la herramienta 2 en 1 Campbell Hausfeld SB3232 también se pueden usar con las grapadoras: Senco
LN4450, SJS-LR, SKS L11-15, Hitachi N3804A, Duofast BN-1832S, KN-1848, ST-18, Stan-Tech SDS 18-14, Atro Minor 90/30, 90/32,
90/40, y Porter Cable NS100.
Calibre Fusión de Grapas Grapas
Modelo # Longitud de la grapa Corona Punta Acabado la linea por linea por caja
FN158K00 12,7mm (1/2”) Calibre 18 6,4mm(1/4") Cincel Galvanizado/Cubierta por vinilo Adhesivo 100 5000
FN168K00 15,9mm (5/8”) Calibre 18 6,4mm(1/4") Cincel Galvanizado/Cubierta por vinilo Adhesivo 100 5000
FN208K00 19,1mm (3/4”) Calibre 18 6,4mm(1/4") Cincel Galvanizado/Cubierta por vinilo Adhesivo 100 5000
FN258K00 25,4mm (1/4”) Calibre 18 6,4mm(1/4") Cincel Galvanizado/Cubierta por vinilo Adhesivo 100 5000
Sujetadores