background image

FP2048, FP2049

3

Installation

(Continued)

Do not use a

grounding adapter with this product!

2. If repair or replacement of cord or plug

is necessary, do not connect grounding
wire to either flat blade terminal. The
wire with insulation having an external
surface that is green (with or without
yellow stripes) is the grounding wire.

Never connect 
green (or green and

yellow) wire to a live terminal.

3. Check with a qualified electrician or

serviceman if grounding instructions
are not completely understood, or if in
doubt as to whether product is
properly grounded. Do not modify
plug provided; if it will not fit outlet,
have proper outlet installed by a
qualified electrician.

Overheating, short 
circuiting and fire

damage will result from inadequate
wiring, etc.

Operation

Definition of Terms

Regulator

- The regulator controls the

amount of air pressure released at the
hose outlet.

ASME Safety Valve

- This valve

automatically releases air if the tank
pressure exceeds the preset maximum.

Handle 

- Designed to move the

compressor.

Drain Valve

- This valve is located on

the bottom of the tank. Use this valve
to drain moisture from the tank daily
to reduce the risk of corrosion.

Reduce tank pressure below 10 psi,
then drain moisture from tank daily to
avoid tank corrosion. Drain moisture
from tank by opening the drain valve
located underneath the tank.

!

CAUTION

!

WARNING

!

DANGER

LUBRICATION

This is an oilless product and 

DOES

NOT

require lubrication to operate.

BEFORE FIRST START-UP

BREAK-IN PROCEDURE 

(Complete this procedure before using
compressor for the first time. Once
completed, it is not necessary to
repeat.)

1. Turn regulator knob fully clockwise

(to the right) to open air flow.

2. Turn on/off switch to OFF position.

3. Plug in power cord.

4. Turn on/off switch to ON position

and run compressor for 5 minutes.

5. Turn on/off switch to OFF position.

6. Unplug power cord.

The compressor is now  ready for use.

BEFORE EACH START-UP

OPERATING PROCEDURE 

1. Turn regulator knob fully

counterclockwise (to the left) to close
air flow. 

2. Connect air hose to outlet of

regulator.

3. Turn on/off switch to OFF position.

4. Plug in power cord.

5. Turn on/off switch to ON position

and let compressor run until it
reaches automatic shutoff pressure.

6. Attach tire chuck or tool to end of

hose.

7. Turn regulator knob clockwise (to

the right) to desired pressure of tool
being used.

On/Off cycling of compressor

In the ON position, the compressor
pumps air into the tank. When a shut-
off (preset “cut-out”) pressure is
reached, the compressor automatically
shuts off.

22 Sp

Compresores Sin Aceite

Handle

Regulator

ON/OFF Switch

Drain Valve

Figure 2 - Unit Identification

Safety Valve

Guía de diagnóstico de averías (Continuación)

Problema

Posible(s) Causa(s)

Acción a tomar

1. Demasiada agua en el tanque

2. Humedad elevada

1. Presostato defectuoso
2. Válvula de seguridad defectuosa

1. Demasiada condensación en el

tanque

2. Conexiones flojas (accesorios, tubería,

etc.)

1. Drene el tanque, incline el tanque para eliminar la

humedad

2. Llévelo a un área menos húmeda, utilice un filtro de

aire de línea

Nota: 

La condensación de agua no es una causa para

el malfuncionamiento del compresor.

1. Cambie el interruptor de presión
2. Cambie la válvula de retención con un repuesto

original

1. Drene con más frecuencia

2. Revise todas las conexiones con una solución de agua

y jabón. Si se detecta una fuga, apriete. O quite la
conexión y aplique cinta para tuberías a las rocas y
vuelva a armar.

Exceso de humedad en
el aire de descarga

El compresor funciona
en forma continua y la
válvula de seguridad se
abre cuando aumenta
la presión

Arranques y paradas
excesivas

Gauge of Cord

18

18

16

14

14

12

12

10

10

Extension cords for 120V/2.5 Amp Unit

Length of Cord (ft)

25

50

100

150

200

250

300

400

500

www.chpower.com

Summary of Contents for FP2048













Reviews: