background image

5

If a top connection is employed, it is 

important to ensure that the plummet stop 

is fitted inside the stove insert. The plummet 

stop prevents damage to the flue baffle 

during chimney-sweeping operations.

Ball/plummet stop

Assembly 

The top stone unit and the cast-iron grill 

must be fitted before the flue pipes are 

assembled. In the case of the Art Modern 

model and the Art Pierre model , the entire 

soapstone casing must be fitted at this 

stage. The Art Étage and Moderne model 

is equipped with a front grill and has no 

top grill.

Impotant!

Study the user instructions carefully before using the stove and 

remember that the installation must be first approved by a chimney 
sweep.

The right location

When you are deciding where the stove is to be placed, it is important to select a central 

location in your house in order to ensure even distribution of heat. If you are also plan-

ning to install a chimney, it is an advantage if the chimney exit point is as close to the 

roof ridge as possible, since this entails both aesthetic and cost benefits. If there is a floor-

level above the stove, you should also think about how the chimney is to pass through it. 

A cupboard or a corner area is often a good location for a flue shaft. The floor surface 

on which the stove is to rest must be even and horizontal.

Order of assembly for top connection

Follow the chimney supplier’s instructions carefully. Assembly is accomplished 

in the following order:

1.  Prepare air-feed to the hearth (if required).

2.  Cut hole in ceiling.

3.  Install the fireplace base.

4.  Lift the stove into position and fit the top stone unit in place (where 

applicable).

5.  Fit soapstone units and top grill (where applicable).

Assemble the chimney. 

The Camina Art Pierre model with a top 

connection to the NVI chimney, featuring 

a grey-coated initial section and a curved 

fireplace base in toughened glass.

Top connection to the Camina NVI 2000 chimney kit

Start by fitting the adapter pipe, using 

stove sealant (see photo). The next stage 

is to fit the connection piece and the flue 

modules, in accordance with the chimney 

manufacturer’s instructions.

If there is a gap between the stove and 

the connection piece, insulate it with carb-

wool, rockwool, or a similar material. Then 

insert the flue pipes to achieve a tight fit 

against the stove.

Summary of Contents for Art Supreme













Reviews: