Cameron BARTON 580A User Manual Download Page 6

Page: 6 / 56

Section 1

Model 580A Differential Pressure Switch

Specifications

General

Actuating Unit (DPU) ...................... Model 224 DPU

Dial Size ......................................... 6 inches (150 mm)

Service Conditions (Normal)........... 40°F (4.4°C) to +180°F (+82.2°C) @ <90% R.H.

Switch Repeatability ....................... ±1% of calibrated span

Switch Set-point Range .................. 10 to 90% of calibrated span

Switch Deadband ........................... ±10% of calibrated span (maximum)

Switch Type .................................... Mechanical, Snap-Acting; both switches are SPDT

Activation ........................................ Increasing or decreasing scale

Switch Contact Rating:

5.0 Amps @ 125 VAC

5.0 Amps @ 250 VAC

3.0 Amps @ 30 VDC (resistive)

1.0 Amp @ 30 VDC (inductive w/arc suppression)

0.4 Amp @ 125 VDC (resistive)

0.2 Amp @ 125 VDC (inductive w/arc suppression)

Input Range .................................... 0-30" WC to 0-650 psid

Indicator Accuracy .......................... ±2.0% of calibrated span (for ranges to 400 psid)

1,2

Indicator Repeatability .................... ±0.5% of calibrated span

Safe Working Pressure ................... 500, 1000, 1500, 3000, or 6000 psig

Maximum Overrange ...................... To safe working pressure

Process Connections...................... 1/4" x 1/4", 1/4" x 1/2", 1/2" x 1/4" and 1/2" x 1/2"

(top x bottom)

Electrical Connections .................... Female, 3/4" NPT, 20 ft., color-coded Tefzel®

insulated 18 AWG wire (40 ft. leads available by

special order)

Torque Tube Rotation ..................... 8° (nominal)

± 2.5% of calibrated span for ranges between 400 and 600 psid; ±6% for ranges over

600 psid.

Additional 2% is applicable near the switch setpoints (±10% span).

Nuclear Qualifications

The following nuclear qualification applications are based on Cameron Engi

neering Report 9A-CR3-580A-29 and 9A-CR3-580A31.

Design Basis Event (DBE) Performance Error

(% of calibrated span):

Radiation (1 x 10

Rads) ................ ±10%

Seismic (12.5 Gs):

During Event ................................... ±10%

Following Event .............................. ±5%

Harsh Environment (≤ 200°F):

During Event ................................... ±10%

Following Event .............................. ±10%

Includes the cumulative effect of accelerated aging.

Summary of Contents for BARTON 580A

























































Search results

Summary of Contents for BARTON 580A

Reviews:

Related manuals for BARTON 580A

Brands by name

Popular brands

Cameron BARTON 580A, User Manual

Search results

Summary of Contents for BARTON 580A

Reviews:

Related manuals for BARTON 580A

Brands by name

Popular brands