Cameron BARTON 580A User Manual Download Page 2

Page: 2 / 56

Safety

Before installing this product, become familiar with the installation instruc-

tions presented in Section 3, Appendix A and all safety notes throughout.

WARNING: This symbol identifies information about practices or circum

stances that can lead to personal injury or death, property damage, or

economic loss.

CAUTION: Indicates actions or procedures which if not performed correctly

may lead to personal injury or incorrect function of the instrument

or connected equipment.

IMPORTANT: Indicates actions or procedures which may affect instrument operation or

may lead to an instrument response that is not planned.

Changing Switch Set Point ......................................................................... 20

Definitions of Terms

................................................................................. 20

Best Practices for Set Points ................................................................... 20

Changing Set Point of an In-Service Instrument (Not Recommended for

Nuclear Qualified Units)

.......................................................................... 21

Changing Set Point of an Out-of-Service Instrument .............................. 22

Range Changes ...................................................................................... 22

Troubleshooting ......................................................................................... 23

Section 4—Assembly Drawing and Parts List

........................................... 25

Section 5—Dimensional Drawings

............................................................. 33

Appendix A—Model 224 DPU

....................................................................A-1

DPU Description ........................................................................................A-1

Specifications

.........................................................................................A-1

Theory of Operation ...............................................................................A-3

DPU Installation .........................................................................................A-4

General...................................................................................................A-4

Mounting.................................................................................................A-5

Piping .....................................................................................................A-5

Piping Diagrams .....................................................................................A-6

Startup ..................................................................................................A-12

DPU Maintenance ....................................................................................A-12

DPU Cleaning and Inspection ..............................................................A-13

Changing the DPU Range ....................................................................A-14

Replacing the Bellows Unit Assembly (BUA) .......................................A-14

DPU Troubleshooting ...............................................................................A-15

DPU Assembly Drawing and Parts List ....................................................A-17

DPU Dimensional Drawing ......................................................................A-19

Summary of Contents for BARTON 580A

























































Search results

Summary of Contents for BARTON 580A

Reviews:

Related manuals for BARTON 580A

Brands by name

Popular brands

Cameron BARTON 580A, User Manual

Search results

Summary of Contents for BARTON 580A

Reviews:

Related manuals for BARTON 580A

Brands by name

Popular brands