CAME G4140IZU, Installation Manual

Page: 17 / 32

Pa
g.
17
- M
an
ua
l c
od
e:
11
9G
V2
9
v
er
.
2.
0
0
9/
20
10 © C
AM
E c
an
ce
lli a
ut
om
at
ic
i s
.p
.a
. -
Th
e d
at
a a
nd i
nf
or
m
at
io
n r
ep
or
te
d i
n t
hi
s i
ns
ta
lla
tio
n m
an
ua
l a
re s
us
ce
pt
ib
le t
o c
ha
ng
e a
t a
ny t
im
e a
nd w
ith
ou
t o
bl
ig
at
io
n o
n C
AM
E c
an
ce
lli a
ut
om
at
ic
i s
.p
.a
. t
o n
ot
ify u
se
rs
.
3
4
2
1
WARNING! The
release procedure may
constitute a hazard for the
user when, for whatever
reason – the bar is fixed
improperly to the housing
during assembly, or the bar
is cracked or broken in an
accident, and so on – the
tension springs no longer
provide balance! These
can thus cause a bru-
sque rotation of the bar
attachment and/or of the
bar itself .
5.9 Manual release of the barrier
- Insert the key into the lock and turn it clockwise. Manually raise the bar and block it again by turning the key
counter-clockwise.
6 Description control panel
FUSES
protection: fuse type:
Motor/s 10A-F
Electronic board (power supply line) 3.15A-F
Accessories 2A-F
Control devices 630mA-F
TECHNICAL FEATURES
Power supply 120V - 50/60Hz
max. rated power 300W
Power draw when idling 25W
Max power of 24V accessories 40W
Insulation rating II
Material ABS
This product is engineered and manufactured by CAME
cancelli automatici s.p.a. and complies with current safety
regulations. Guaranteed 38 months if not tampered with.
The control panel works on 120V a.c. of power, 50/60Hz
frequency.
Both command and control devices and accessories are 24V
powered. Warning! Accessories must not exceed 40 W overall.
The control unit is fitted with an amperometric device which
constantly regulates the motor’s drive coefficient.
When the bar runs into an obstacle, the amperometric sensor
immediately detects an overcharge in the drive and redirects
the gate’s direction of movement, and:
- during opening: the bar stops
- during closing: the bar reverses its direction until it opens com-
pletely; automatic closure is thus activated.
Caution! After three consecutive direction reversals, the bar will
remain up and automatic closure will be discontinued. To close the
gate, use the radio remote control or the
push-button.
All connections are protected by quick fuses, see table.
The card provides and controls the following functions:
- automatic closing after an open-command
- immediate closure
- pre-flashing by the motion indicator
- obstacle detection when gate is still in any position
- slave function
- function that increases the braking action of the barrier.
The following command modes are possible:
- open/close
- open/close and maintained action
- open
- complete stop.
Apposite trimmers regulate:
- the automatic closing run time
- the amperometric device’s detection sensitivity
Optional accessories
:
- Flashing Crown and Luminous band.
- bar open light marks the position of opening of the bar; it turns
off after the closing operation
;
- LB38 Card, provides power supply through a battery, in case of
a power outage. When power comes back on, it also recharges
the batteries (see relative technical literature).
Warning! Before acting on the machinery, cut off the main power
supply and disconnect any emergency batteries.