background image

- pag. 

- pag. 

- pag. 

- pag. 

- pag. 

10

10

10

10

10

 - english -

 - english -

 - english -

 - english -

 - english -

SELECTION FUNCTION

ZL37B CONTROL PANEL

1

2

3

4

5

6

7

8

9

10

ON

OFF

5 = funcion

flashing light en opening

and closing

ON OFF
activated deactivated

5

5

6 = function

obstacle detection

(with motor at end of

travel)

ON OFF
activated deactivated

6

6

2 = funcion

"open-close-inversion"

by radio remote control

(when receiver is installed)

ON OFF
deactivated activated

2

2

2 = function

"open only"

by radio remote control

(when receiver is installed)

ON OFF
activated deactivated

2

2

3 = funcion

24V output during

movement and in the closed

position

ON OFF
activated deactivated

3

3

3 = function

24V output during

movement

ON OFF
deactivated activated

3

3

9

9 = function

total stop

ON OFF
deactivated activated

9

- connect safety device
across 1-2

8

8 = function

immediate closure

8

- connect safety device
across 2-C5;
- deactivate automatic
closure (1 OFF)

7

7 = function

slave

ON OFF
activated deactivated

7

10

10 = function

increase braking action on

barrier bar

ON OFF
activated deactivated

10

4 = funcion

"human presence"

ON OFF
activated deactivated

4

4

1 = function

automatic closure

ON OFF
activated deactivated

1

1

- deactivated immedia-
te closure (8 ON)

2

1

3

4

5

6

7

8

9 10

0

Rall.

Vel.

7

4

ON OFF
deactivated activated

Summary of Contents for G12000 Series


















Reviews:

Related manuals for G12000 Series