background image

9  - 24803960 15-09-2014 

 

(*) There’s a built-in overcharge protection over for the power 
supply line.

‘Standard’ confi guration 

Basic installation diagram 

 

24 VAC power supply;

 

STP AWG#22;

 

Back of connection module;

 

Front of connection module;

 

Keyboard;

 

8 Alarm inputs- 2 Aux outputs;

 

Common (RX+/RX-);

 

Heating 24 VAC;

  

24 VAC power supply;

 

RS485 - HALF DUPLEX mode;

Connecting the videocamera to the DVR 

Connecting the videocamera to the controller via 
connection module 

Connecting the videocamera and controller via 
connection module 

Features 

 

ID selecting switches;

 

Selecting communication protocol and line terminal;

 

Alarm inputs from 1-4 - Relay output 1;

 

Alarm inputs from 5-8 - Relay outputs 2;

 

24 VAC heating system;

 

Fan/Heating system;

 

Power supply/Common;

 

Setting up the video system.

Setting up the video system 

SW2

1

2

3

4

NTSC

OFF

x

x

x

PAL

ON

x

x

x

Analog Dome

x

OFF

x

x

Web Dome

x

ON

x

x

Setting up the Web baud rate 

S6

1

2

3

4

4800

x

x

OFF OFF

9600

x

x

OFF ON

19200

x

x

ON OFF

38400

x

x

ON

ON

Line terminal 

Every device connected to the end of the data communication 
line must terminate by setting up a DIP switch or, for example, a 
terminal jumper to prevent possible errors in the command signal.

S4

1

2

3

4

Terminated

ON

x

x

x

Not terminated

OFF

x

x

x

Pull Up/Down (*)

x

x

ON

ON

Normal (*)

x

x

OFF OFF

The total cable length for communication must not exceed 1.2 km.
(*) Set ups in case of communication errors. positions 2 and 3 
must always be set up in the same way (Both set to on ON or 
both set to OFF).

ID set up 

Each Dome videocamera must have a univocal ID address. When 
installing several Dome videocameras used with one DVR, the 
videocamera’s ID must be the same as that as the DVRs input.

To set up the videocamera’s ID and for selecting the protocol, refer 
to the fi gure shown below:

Dome ID S3

S2

S1

001

0

0

1

.

.

.

999

9

9

9

Setting up the installation environment

S7

D1

D2

Inside

OFF

OFF

Outside

ON

OFF

Defrosting

ON

ON

Setting up protocols 

The videocamera can communicate with various protocols if the 
communication speeds are the same. For setting up the protocols 
refer to the following tables.

Protocol

D1

D2

D3

D4

AUTO Selection (no parity)

OFF OFF OFF OFF

AUTO selection (even parity)

ON OFF OFF OFF

PP

OFF ON OFF OFF

NUVICO

ON ON OFF OFF

S2

OFF OFF ON OFF

PD

ON OFF ON OFF

VC

OFF ON ON OFF

SN

ON ON ON OFF

DC

OFF OFF OFF ON

PS

OFF ON OFF ON

VL

ON OFF ON ON

Summary of Contents for bpt Brahms XTWV36ST

















Reviews: