TITLE
11
commissioning via panel
Ensure the wiring is complete (refer to the wiring diagram), the micro limit switch end-of-travel points are set
(refer to the ATS manual) & any required physical stops are set before commencing with programming
Tick
1. Power on the control panel.
2. Press and hold the
button for 2 seconds to access programming,
F
1
appears on the display.
3. Disable total stop –
F
1
-
O
F
F
4. Disable safety inputs –
F
2
&
F
3
–
O
F
F
5. Set the number of motors –
F
4
6
–
O
F
F
6. Set the motor type –
A
1
–
4
7. Check the motor direction –
A
2
–
O
N
For motor 2, Press and hold
.
The gate should open, if not reverse the motor cables for motor 2
(Connections
M2
,
N2
). Leave the gate in the halfway position.
For motor 1, Press and hold
. The gate should open, if not reverse the motor cables for motor 1
(Connections
M1
,
N1
). Leave the gate in the halfway position.
8. Setup the encoder –
A
3
–
O
N
The Gates will now perform a close and open cycle.
9. Exit the programming using the
button.
10. Check the gate operation by pulsing across connections 2 & 7, the gate will close.
Important!
The installation must be carried out
by skilled and qualified personnel
Should the gates not operate as suggested above,
call CAME helpline
0115 921 0430
for technical support.
Safety inputs should now be configured and the gate force tested as required.
Please refer to the full manual to complete the commissioning.
button - used to perform the following operations:
• Exit the menu • Delete the changes • Go back to the previous screen
buttons - used to perform the following operations:
• Navigate the menu • Increase or decrease values
button - used to perform the following operations
• Access menus • Confi rm a choice
1
2
3
1
2
3
11
commissioning
via panel
Should the transmitter not operate as suggested above,
call CAME helpline
0115 921 0430
for technical support.
add
a transmitter button
1.
Press and hold the
button for 2 seconds to access programming. (
F
1
appears on the display).
2.
Add a transmitter button -
U
1
3.
Choose the function to be assigned to the button
1
= Step-by-step
2
= Sequential
3
= Open
4
= Partial opening
4.
A fl ashing number will now appear on the screen.
5.
Press and release a button on a transmitter, the number on the screen will increment by one for
each button pressed. A maximum of 250 individual buttons can be saved.
remove
a transmitter button
1.
Press and hold the
button for 2 seconds to access programming. (
F
1
appears on the display).
2.
Remove a transmitter button -
U
2
–
O
N
3.
Use the arrow buttons to choose the number associated with the transmitter button you wish to remove.
“
C
L
R
” will appear to confi rm deletion
remove
all transmitters
1.
Press and hold the
button for 2 seconds to access programming. (
F
1
appears on the display).
2.
Remove all transmitters –
U
3
–
O
N
All transmitters will be deleted.
transmitter
radio decoding
1.
Press and hold the
button for 2 seconds to access programming. (
F
1
appears on the display).
2.
Remove a transmitter button –
U
4
3.
Choose the type of radio coding for the transmitters
1
= All decoding (default)
2
= Rolling code
4
= TW key block
Ensure the AF card is fi tted (refer to the wiring diagram).
Summary of Contents for 8K01MP-0408
Page 30: ...TITLE notes...
Page 31: ...TITLE notes...
