background image

i

The exclamation point within an equilateral
triangle is intended to alert the user of the
presence of important operating and main-
tenance (servicing) instructions in the lit-
erature accompanying this product.

CAUTION: 

 TO PREVENT ELECTRIC

SHOCK, MATCH WIDE BLADE OF PLUG
TO WIDE SLOT, INSERT FULLY.

ATTENTION:

 

POUR EVITER LES CHOCS

ELECTRIQUES, INTRODUIRE LA LAME LA PLUS
LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQU’AU FOND.

WARNING:

TO PREVENT FIRE OR
SHOCK HAZARD, DO NOT
EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE
.

IMPORTANT NOTICE

The serial number for the subwoofer is located
on the subwoofer’s control panel. Please write
this number down and keep it in a secure area.
This is for your security.

IMPORTANT

The lightning flash with arrowhead, within
an equilateral triangle, is intended to alert
the user of the presence of uninsulated
“dangerous voltage” within a product’s en-
closure that may be of sufficient magnitude
to constitute the risk of electric shock to
persons.

SHOCK HAZARD

DO NOT OPEN

WARNING

TO PREVENT THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE SUBWOOF-
ER’S COVER. NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.

RISQUE DE CHOC ELECTRIQUE

NE PAS OUVRIR

AVIS

POUR EVITER TOUT RISQUE DE CHOC
ELECTRIQUE, NE PAS DEMONTER LE
COUVERCLE DU HAUT PARLEUR.
AUCUN ENTRETIEN DES PIECES
INTERIEURES N’EST REQUIS.TOUT
SERVICE D’ENTRETIEN NE DOIT ETRE
EFFECTUE QUE PAR DU PERSONNEL
D’ENTRETIEN QUALIFIE.

READ AND HEED IMPORTANT SAFETY WARNING

ON BACK OF SUBWOOFER ENCLOSURE

Summary of Contents for Powered Subwoofer
















Reviews: