background image

1

PRODUCT SPECS

WARNING 

To reduce the risk of  INJURY or DEATH: 

• Never let  children  operate  the  gate  or  play  around the  gate. Keep the remote control away

from children.

• Always keep people and objects away from the gate. Cars, people, and other objects should

never enter when the gate is closing.

• Test  gate operator monthly. The  gate must  reverse when it comes in contact  with a solid

object, or stop when an object activates the non-contact sensors. After adjusting the force or

travel limit, re-test the gate operator. Failure to maintain the gate operator properly can

increase the risk of injury or death.

• Use the emergency release only when the gate is not moving.

• Keep  the  gate  properly  maintained.  Read  the  owner's manual on how to maintain your gate.

Have a certified service technician make repairs or install gate operator hardware.

• The gate entrance should be used for vehicles only. Pedestrians should use a seperate entrance.

• Keep these instructions.

Product Specs

Voltage Input: 110V 

Maximum Output Current: 15 amp, Fuse: AC 110V 15 amp 

Remote Control Distance: >150 Feet (50 meters) 

Maximum Gate Weight: 3000 lbs

Maximum Gate Length: 50 Feet

• Verify this operator is proper for the type and size of gate.

• Make sure the gate has been properly installed and slides freely in both directions. Repair

or replace all worn or damaged gate hardware prior to installation.

LANGUAGES

To download this user manual in a different language, visit calimetco.com/manuals

 

Para descargar este manual de usuario en otro idioma, visite calimetco.com/manuals

Summary of Contents for CM-5-ACFP






















Reviews: