CALIFORNIA ACCENT LIGHTING, INC.
2034 E. Lincoln Ave. #431, Anaheim, CA 92806
ph. 800.921.CALI (2254) or 714.535-7900 \ fx. 714.535.7902
[email protected] \ calilighting.com
© CALI. All rights reserved. CALI reserves the right to make changes or withdraw specifications without prior notice.
Installation Instructions
Overview
lip
LEDs
™
LLED
8600-RME
1 of 21
End View
Extrusion
(#LLED8600-RME)
1.38”
.75”
.60”
.70”
1.80”
Power Connector
(#LLED8600-PC)
RGBW StripLite
(#LLED8600)
Frosted Lens Cover
(#LLED8600-RME-LF)
IMPORTANT
VERIFY CORRECT
LUMINAIRE WAS RECEIVED WITH
CORRECT COLOR TEMPERATURE
AND VOLTAGE BEFORE CUTTING
OR INSTALLING.
CALI
WILL NOT
BE RESPONSIBLE IF INCORRECT
LUMINAIRE IS INSTALLED.
• Electric compound miter saw
• 14.4 to 28 volt cordless drill
• Drill bits - concrete or wood
• Electrical cords
• Safety glasses
• Marker
• Electric hammer drill (optional)
• Phillips bits - sufficient quantity
• Electrical three ways
• Measuring tape
• Chalk line
• Sharp scissors
• Soldering iron with kit
PRODUCT INFORMATION
• For accent, cove, edge, under cabinet lighting
• 24 volts DC for easy and safe installation
• Long life, energy efficient LEDs
• Maximum run based on 5 Amps: 21’ (5.5W), 26’ (4.5W)
For class II applications: 17’ (5.5W), 21’ (4.5W)
• Can be ordered to specific lengths for easier installation when exact
dimensions are known (Example: 10x10’6”)
• Plug and light system
• Lead wires are typically 33” long and exit on one end
ELECTRICAL
• LipLEDs products require a 24 volt DC remote
trans
FORMER
• To calculate transformers size find watts per foot
(Example: 4.5W per foot)
• Determine length in feet (Example: 10’)
• Calculate Load: Multiply Watts per Foot x Length in Feet
(Example: 4.5W x 10’= 45W)
• Choose an electronic
trans
FORMER from catalog (Example: TRA60-E)
• Determine maximum distance using Maximum Wire Length Table
(Example: 45 watts is between 40W and 80W. Using #14 wire,
maximum distance is 37’ from
trans
FORMER to first LED)
INSTALLATION TOOLS REQUIRED
INSTALLATION RECOMMENDATIONS
• LipLEDs LED tape must be mechanically attached
directly to mounting surface using mounting clips or channels
• Conduit raceway should be sleeved at one end for low voltage wires
going to
trans
FORMER
2” increments up to max run
± 0.125” cutting tolerance
*See max run for more information
2”
6” increments up to max run
*See max run for more information
6”
2” increments up to max run
± 0.125” cutting tolerance
*See max run for more information
(Run lengths required)
2”
3.9” or 6.5”
6.5”
2” increments up to max run
± 0.125” cutting tolerance
*See max run for more information
2”
8’ Maximum extrusion and lens length
8’ Maximum extrusion and lens length
(Dry Location field cuttable)
Lens and extrusion shipped in
8’ sections (field cuttable)
8’ Maximum extrusion and lens length
3.95” increments up to max run
± 0.125” cutting tolerance
*See max run for more information
3.95”
LLED8400 --->
LLED8000 --->
LLED8200 --->
LLED8300 --->
LLED8500 --->
LLED8100 --->
Specify Length (19.7”Assembly Increments)
(Add 2.5” to run for end cap and strain relief)
.75”
5.5W
.78”
.52”
*1.5W, 2.5W,
3.6W, 4.5W
.47”
.36”
6.5” (2.5W) or 3.9” (5.5W) increments up to max run
± 0.125” cutting tolerance
*See max run for more information
6.5“ increments up to max run
± 0.125” cutting tolerance
*See max run for more information
3.9”
3.9” increments up to max run
± 0.125” cutting tolerance
*See max run for more information
3.9”
3.9” increments up to max run
± 0.125” cutting tolerance
*See max run for more information
3.9”
3.9” increments up to max run
± 0.125” cutting tolerance
*See max run for more information
