California Accent Lighting lipLEDs LLED8600-RME Installation Instructions Manual Download Page 17

Page: 17 / 21

CALIFORNIA ACCENT LIGHTING, INC.

2034 E. Lincoln Ave. #431, Anaheim, CA 92806

ph. 800.921.CALI (2254) or 714.535-7900 \ fx. 714.535.7902

[email protected] \ calilighting.com

Installation Instructions

lip

LEDs

™

LLED

8600-RME

17 of 21

Mounting Channel (Dry Location)

Measure area where LLED8600-RME will be installed.

RECOMMENDATION:

Use chalk line to ensure a straight installation.

Drill holes as needed with drill bit and countersink.

Screw channel to desired surface using countersink holes.

NOTE:

Surface must be flat.

Remove adhesive backing from lightstrip, then install into channel.

LLED8600

Channel

Remove adhesive backing

Lightstrip
is secured
to channel

Countersink hole

Conduct continuity test.

Set voltmeter to DC voltage, then test power source before connecting.

If a conductive
path is formed
between positive
and negative wire,
the multimeter will
beep. You need to
trouble shoot to
find the short.

If there is no
conductive path, the
multimeter will not
beep.

Troubleshoot

Good

VAC

OFF

VDC

COM

VΩ

VAC

OFF

VDC

COM

VΩ

+ -

DCA

OFF

DCV

COM

VΩ

+ -

VAC

OFF

VDC

COM

VΩ

VAC

OFF

VDC

COM

VΩ

+ -

DCA

OFF

DCV

COM

VΩ

+ -

Confirm the correct
voltage, depending on
the light strip.

Power source

DCV

VAC

OFF

VDC

COM

VΩ

VAC

OFF

VDC

COM

VΩ

+ -

DCA

OFF

DCV

COM

VΩ

+ -

Snap lens into channel.

Ensure lens is
secured in place

Ensure screw is
flush with channel

Connect power source to power connector. See wiring diagram (page 6).

TIP:

If LEDs do not turn on, flip polarity (+,-) or power source connection to

power connector.

Summary of Contents for lipLEDs LLED8600-RME






















Search results

Summary of Contents for lipLEDs LLED8600-RME

Reviews:

Related manuals for lipLEDs LLED8600-RME

Brands by name

Popular brands

California Accent Lighting lipLEDs LLED8600-RME, Installation Instructions Manual

Search results

Summary of Contents for lipLEDs LLED8600-RME

Reviews:

Related manuals for lipLEDs LLED8600-RME

Brands by name

Popular brands