11
42” GRILL LP GAS HOOK UP (TYPE 1 OR QCC1 REGULATOR):
Grills orificed for use with LP gas come equipped with a high capacity hose/regulator assem bly for connection to
a standard 20 lb. LP cylinder (Type 1). The LP tank is not included.
Connection:
1/2” NPT male with a 3/8” Flare adapter (included). LP Hose with a quick disconnect and fittings are
included. Operating pressure: 11.0” W.C.
CAUTION!
Before connecting LP tank to regulator, check that all grill burners and side burners, smokers, and rotisserie valves
are in the OFF position and open grill lid.
To connect the LP regulator/hose assembly to the tank/valve assembly, first make sure the main valve on the tank is
completely closed. Although the flow of gas is stopped when the Type 1 system is disconnected as part of of its safety
feature, you should always turn off the LP tank main valve after each use and during transport of the tank or unit. Insert
the regulator inlet into the tank valve and turn to the black coupler clockwise until the coupler tightens up. Do not over-
tighten the coupler. Turn the main tank valve on and turn the burner control valves on the unit to the “HI” position for
about 20 seconds to allow the air in the system to purge, turn valves off and wait 5 minutes before attempting to light the
burners.
To disconnect the coupler, first make sure the main tank valve is turned off. Grasp the coupler and turn counter clock-
wise. The inlet will then disengage. Remove the inlet from the tank valve opening if it has not already done so when it
disengaged. Your local LP filling station should be equipped with the proper equipment to fill your tank.
LP TANK REQUIREMENTS:
A dented or rusty LP tank may be hazardous and should be checked by your LP supplier. The cylinder that is used must
have a collar to protect the cylinder valve. Never use a cylinder with a damaged valve. Always check for leaks after ev-
ery LP tank change. The LP gas cylinder must be constructed and marked in accordance with the specifications for LP
gas cylinders of the U.S. Department of Transportation (DOT or CAN/CSA-B339) and designed for use with a Type
1 system only. Do not change the regulator/hose assembly from that supplied with the unit or attempt to use a Type 1
equipped regulator/hose assembly with a standard 510 POL tank/valve assembly. The cylinder must be provided with
a shut-off valve terminating in an LP gas supply cylinder valve outlet specified, as applicable, for connection Type 1. If
the appliance is stored indoors, the cylinder must be disconnected and removed from the appliance. Cylinders must be
stored outdoors in a well-ventilated area out of the reach of children.
Note:
When an LP unit is being directly connected to an LP house
system, you must follow the natural gas hook up guidelines.
The installer must provide the proper gas regulator to reduce
the gas flow to 11” W.C.
Note:
The Grill comes with the LP Regulator/Hose assembly installed
at the factory. The assembly, along with the entire Grill system,
is leak tested. Do not remove the Regulator/Hose assembly
from the Grill during installation.
WARNING
:
»
Do not remove the Grill from the pallet until you are
ready to install.
»
Do not place the Grill directly on the ground or any other
flat surface without support. This will prevent damaging
the regulator/hose assembly by the weight of the grill.
»
Check the hose, regulator and connectors for damage.
Look for cracks, abrasions, brittleness, holes, dents and nicks.
»
Do not attempt to remove, repair, or replace the Regulator/
Hose assembly by yourself. It must be done by a
qualified licensed technician only.
*Installation must conform with local codes or with
the National Fuel Gas Code ANSi Z223.1 or the
CAN/CGA-B149.2 Propane Installation Code
Type 1 Regulator
LP Regulator hose
assembly 11” W.C.
20 lb LP Tank
Main Tank Valve
1/2” female NPT from unit
connection to 3/8” male
flare of L.P. hose assy
Bottom of unit
Summary of Contents for CGP42-2G-1SR-L N WH
Page 31: ......
