Calex PMB201 Operator'S Manual Download Page 15

15

ACCESSING CONNECTED SENSORS VIA ANOTHER MODBUS MASTER

If the PM180 is connected to another Modbus Master, such as a Modbus PLC or SCADA, the 

entire sub-network (the PM180, the connected sensors and output modules) appears as a 

single Modbus Slave device to the PLC or SCADA. The Modbus Slave ID (Modbus Address) is 

that of the PM180. 
The temperatures and settings of the sensors connected to that PM180 can be read by 

adding the following offsets to the sensor’s own Modbus register addresses. The Sensor Index 

is the position of the sensor in the PM180 sensor list. The Sensor Index numbers correspond 

to the positions of the sensors on the PM180 screen as follows: 

0

1

2

3

4

5

Sensor Index

Address offset (hex)

Address offset (decimal)

0

0x1000

4096

1

0x1100

4352

2

0x1200

4608

3

0x1300

4864

4

0x1400

5120

5

0x1500

5376

Example

To read the Filtered Temperature on a PyroMiniBus sensor in position 4 on the PM180 as 

shown above, read from register 0x0E + 0x1400 = 0x140E = decimal 5134.
For information on the Modbus addresses for other compatible sensors, please see the 

Operator’s Guide for that sensor. 

MAINTENANCE

Our customer service representatives are available for application assistance, calibration, 

repair, and solutions to specific problems. Contact our Service Department before returning 

any equipment. In many cases, problems can be solved over the telephone. If the sensor is 

not performing as it should, try to match the symptom below to the problem. If the table does 

not help, call Calex for further advice.

GUARANTEE

Calex guarantees each instrument it manufactures to be free from defect in material and 

workmanship under normal use and service for the period of two years from the date of 

purchase. This guarantee extends only to the original buyer according to Calex Terms and 

Conditions of Sale. 

Summary of Contents for PMB201

















Reviews: