background image

201-2001

heat interface unit

5

Hydraulic connections

The whole system should be thoroughly flushed to remove
any debris that may be in the supply pipework to the HIU and
to the domestic hot water pipework in the apartment before
connecting the HIU.

Fix the HIU to the wall

N.B.

: the wall anchors (not supplied) can only guarantee

effective support if inserted correctly (in accordance with
good technical practice) into walls built using solid or
semi-solid bricks. If working with walls built using perforated
bricks or blocks, mobile dividing panels or any masonry walls
other than those indicated, a preliminary static test must be
carried out on the support system. 

Electrical

1

electric supply line 230 V (ac) – 50 Hz - 3A.

Electrical Schematic

Schematic

Installation

The  201-2001  HIU is  designed  for  installation  in  a  sheltered
domestic environment (or similar), therefore cannot be installed
or used outdoors, i.e. in areas directly exposed to atmospheric
agents.  Outdoor  installation  may  cause  malfunctioning  and
hazards.

If the device is enclosed inside or between cabinets, sufficient
space must be provided for routine maintenance procedures. It is
recommended that electrical devices are NOT placed underneath
the HIU, as they may be damaged in the event of leakage from
any hydraulic component of connection.

If this advice is not heeded, the manufacturer cannot be held
responsible for any resulting damage.

In the event of a malfunction, fault or incorrect operation, the
device should be deactivated; contact a qualified technician for
assistance.

Preparation

After establishing the position where the HIU will be installed,
perform the following operations:

Mark the holes required for securing the HIU to the wall.

Mark the position of the water pipe connections.

Check the measurements again before installing pipework and
electrical cables.

Hydraulic connections

1

connection to the pipework from the centralised boiler plant

2

space heating circuit connection

3

domestic water circuit connection

L

N

E

230V 3A RATED

L

N

HOT WATER

HEATING ON

ROOM STAT

PROGRAMMER

HEATING

ZONE VALVE

CYLINDER

L
SL

STAT

1

2

3

4

5

6

7

8

9

10

HOT WATER

ZONE VALVE

L

SL

4

5

5

6

7

10

9

14

14

5

8

15

5

Summary of Contents for altecnic 201-2001









Reviews: