background image

 

 

 

 

 

 

 

 

Dokument 
IMA 190 
HFE507 

Rev 

Sid 
35 (44)

 

 

 

Maintenance level 

 

A number of execution options are available from the MAINTENANCE MENU (see 
Table IV). This level is accessed only from the display mode in the 

set points of CO 

and CO

2

 selection. A two buttons push

 

and an access

 

code restricts access, 

intended for competent trained service personnel only. The Entr(+-)command is done 
by PUSHING MENU AND ESC AT THE SAME TIME (hold down for about 10 
seconds). The access code has eight binary digits; one press at MENU(+) equals 1 
and one press at ESC(-) equals 0. The code value can be changed for your personal 
choice from the software UIP 4.0.  
 
Always use the ESC button to return to the DEFAULT mode. Several pushes of the 
ESC button may be needed to return to the DEFAULT mode. The 

Entr(+-)

 push 

(MENU & ESC) eventually leads to execution of functions, which causes temporary 
or permanently change of any parameter, that affects the system outputs! 

 

 

 

 

Function 

Line 

 

Display 

 

Time 

limit 

 

Function description 

4a 

SPCO 

yes 

For setting the 

set point

 of the 

CO 

concentration

4b 

The present 
CO set point 

yes 

For 

increase / decrease

 of the 

CO

 

set point. 

The set point is 

increased by stepping with MENU(+) button. Decreasing is done by 
stepping with the ESC(-) button. 

5a SPc 

yes 

For setting the 

set point

 of the 

CO

2

 

concentration 

5b 

The present 
CO

2

 set point  yes 

For 

increase / decrease

 of the

 CO

2

-concentration set point 

The 

set point is increased by stepping with MENU(+) button. Decreasing 
is done by stepping with the ESC(-) button. 

Table IV

.  Maintenance functions available on M-SENSE III to set output limits. Time limit refers to an 

internal time-out that returns the LCD and maintenance function back to normal. ENTER is a 
simultaneous pressing on MENU and ESC. 

 

 

Summary of Contents for SenseAir M-SENSE III













































Reviews: