background image

Customer Services (858) 578-7887 & (888) GO IN

TEC

IN

TEC

 Controls, 12700 Stowe Dr., Suite 1

0

0, Poway, CA 92064

Fax (858) 578-4633 & (888) FX IN

TEC

www.inteccontrols.com

Specification subject to change without notice.

Printed in USA 140916

September 16, 2014 – 

Revision

Polygard® is a registered trademark of MSR

UMLC1112I01

PolyGard

 CO LC-1112 V3 

Electrochemical analog carbon monoxide transmitters 

serial no. EC-S 002 

User Manual 

August 29, 2006 

 

Specifications subject to change without notice. | USA 140916 | Page 1 of 13

12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.IN

TEC

 | relevantsolutions.com/inteccontrols

LC-1112_V3 – UserManual

Polygard® is a registered trademark of MSR | UMLC1112I01

12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.IN

TEC

 | relevantsolutions.com/inteccontrols

PolyGard

®

 is a registered trademark of MSR-Electronic GmbH | UMLC1112I01

January 04, 2016 – 

Revision

INTEC Controls | 12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.INTEC | inteccontrols.com

February 11, 2020 – 

Revision

Summary of Contents for Intec Controls PolyGard CO LC-1112 V3














Reviews: