background image

SYSTEM MOdE

Your spa is equipped with a System Mode. This function will allow you to conveniently turn the jet(s) on high speed and the light on maximum intensity at the same time.
To activate the system mode, perform the following functions:
Press the SET button until the SYSON symbol is illuminated on the display. Press the TEMP 

 

button to activate the SYSON mode feature. 

The jets and light icons will remain illuminated on the display until the system mode is deactivated.

NOTe:

 Once activated, the jet and light functions can still be changed by pressing the JETS or LIGHT button.

To deactivate the system mode, press the SET button until the SYSON symbol is illuminated on the display. Press theTEMP 

 

button to deactivate

MANUAl ClEAN CYClE

All spas are equipped with a Clean Cycle. When the mode is activated, the jet pump in the first jet system will turn on and run for ten minutes (used for water 

maintenance). To activate the Clean Cycle, press the SET 

button several times until the CLEAN symbol is illuminated on the display. Press the TEMP 

 

button to 

activate the CLEAN cycle feature.

NOTe: 

The jet icon will flash on and off while the Clean Cycle is active. 

To stop the Clean Cycle before the ten minutes is complete, press the SET button several times until the CLEAN symbol is illuminated on the 

display then press the TEMP 

 

button to deactivate. 

NOTe: 

Pressing the JETS button will also deactivate the clean cycle and the jet icon will remain on and solid.

TOOlS MENU

The TOOLS menu is one of the main menus on the control panel. Within the TOOLS menu are seven submenus, which consists of; Temp Lock, Spa Lock, Light, Econ or 

Summer Timer, Filter 1, Filter 2  and Exit. 
To enter into the TOOLS menu, scroll through the main menus using the SET

button until the TOOLS menu is illuminated on the display. Press the TEMP 

 

button to 

enter into the TOOLS submenu, use the SET button to scroll through the submenus. Once the desired submenu is illuminated, press the TEMP 

 

button to activate the 

submenu. To leave the TOOLS submenu, scroll through the submenu until EXIT is illuminated, press the TEMP 

 

button to exit the submenu.

lOCk FEATURES

The two locking features, SPA LOCK and TEMPERATURE LOCK, are enabled from the control panel by pressing the SET button until the TOOLS menu is illuminated. 

Then press the  TEMP 

 

button to enter the TOOLS submenus. Use the SET

button to scroll through the submenus to get to the locking features. Once enabled, a lock 

will remain active until a specific button combination is applied to disable the lock. Even if power is disconnected from the spa and soon thereafter reapplied (such as in a 

power outage) the lock will remain in place.

TEMPERATURE lOCk

The TEMPERATURE LOCK feature deactivates the temperature control function of the control panel. The jets and the light functions will operate 

normally. TEMPERATURE LOCK is most often used by people who do not want others to tamper with or change the set temperature of the spa 

water. TEMPERATURE LOCK is a submenu of the TOOLS menu.
To activate the TEMPERATURE LOCK, press the SET button in the TOOLS submenu until the TLOK- symbol is illuminated on the display. 

Press the TEMP 

 

button to activate the TEMPERATURE LOCK feature (TLOK+).  

When the TEMPERATURE LOCK is activated, the JETS, LIGHT and any other features your spa may have will operate normally, and the temperature setting can be 

viewed but can NOT be changed. If a temperature button is pressed, TLOK will display for several seconds, then turn off.
To deactivate the TEMPERATURE LOCK, press the SET button in the TOOLS submenu until the TLOK+ symbol is illuminated on the display. Press the TEMP 

 

button 

to deactivate the TEMPERATURE LOCK feature. 

SPA lOCk

The SPA LOCK feature deactivates all of the functions of the control panel. It is generally used to prevent unwanted use of the spa. The 

SPA LOCK menu is a submenu of the TOOLS menu.
To activate the SPA LOCK, press the SET button in the TOOLS submenu until SLOK- is illuminated on the display. Press the TEMP 

 button 

to activate the SPA LOCK feature.
When the SPA LOCK is activated, the buttons for the jets, temperature control, light, and any other features your spa may have are deactivated. 

If the Jets, Light, or TEMP 

 or  TEMP 

 buttons are pressed, the SLOK will display for several seconds, then turn off.

To deactivate the SPA LOCK, press the SET button in the TOOLS submenu until the SLOK+ symbol is illuminated on the display. Press the  TEMP 

button to deactivate 

the SPA LOCK feature.

16

OPeraTING INSTrUCTIONS

Summary of Contents for vacanza series









































Reviews: