37
UTOPIA OPERATING INSTRUCTIONS
Spa or Temperature Lock Indicator:
The Spa or Temperature Lock indicator is displayed when either the Spa Lock, Temperature Lock or both are activated.
Lock indicator does not flash.
Jet Pump Indicator:
The Jet Pump indicator is displayed whenever a jet pump is on. The Jet Pump indicator will flash whenever the spa is in the ten-minute
Clean Cycle or Auto Clean Cycle.
Air Jets Indicator:
The Air Jets indicator is displayed whenever the air jets are on and will flash in the Auto Clean Cycle.
Summer Timer Indicator:
The Summer Timer indicator is displayed when the summer timer is set to ON. In summer timer mode, the heater and circulation
pump cycle are off for eight hours. The Summer Timer indicator will not flash.
POWER Indicator:
The POWER indicator is displayed when the spa is properly supplied with power. It also provides a diagnostic function–a flashing power
indicator indicates that the heater high limit has tripped, meaning that either the spa water is above its acceptable temperature range, or a malfunction has
occurred within the spa (such as low circulation due to clogged filters). When the power indicator is not displayed it means that there is a problem with the spa
control box or the power supplied to the spa (see Troubleshooting section for more information).
HOME SCREEN
The temperature displayed in the center of the Home screen is the actual temperature of the spa water. If the READY icon is displayed and solid on the control panel,
then the actual spa temperature is within 1°C (2°F) of the set temperature. The corner soft button functions are as follows:
MEMORY
This feature will recall the last active setting for jets and lights prior to pressing the All Off button.
ALL OFF
This feature will shut jets, lights and audio (if installed) off immediately, while saving the last active jets and lights settings.
AUDIO
If you purchased music or TV accessories with your spa, this feature will take you to the Audio menu.
IMPORTANT:
Some soft key functions will only be illustrated if an available accessory has been installed.
CLEAN
Provided as a convenient timer for water maintenance, this function activates the jet pump on high for a ten minute period. The jet icon will flash to indicate the jet
pump is engaged and in the Clean cycle. During this cycle add properly measured spa water chemicals into the filter compartment. The jet pump and clean icon will
automatically shut off after ten minutes.
TEMPERATURE CONTROL
The set temperature range is from 26°C to 40°C (80°F to 104°F). (The water temperature of any spa may rise or lower slightly depending on the current use and
condition of your spa and on outside temperatures.)
The set temperature of the spa water will automatically be 38°C (100°F) the first time power is applied. This is the setting programmed at the factory. After the spa has
been set up and used, the last temperature value set by the user will be stored in memory. If power is disconnected from the spa, it will automatically revert to the last set
temperature when power is reapplied.
To display the set temperature of the spa:
Press the OPTIONS hard button on the Main Control panel.
Press the soft button next to
Temperature
. The set temperature screen will be displayed. This screen will automatically revert to the Home screen after 45 seconds
of non-use.
To increase the set temperature of the spa water:
Press the OPTIONS hard button on the Main Control panel.
Press the soft button next to
Temperature
.
Press the soft button next to ▲. Each time the button is pressed, the set temperature display will increase by .5
°
C. If the button is held down, the set temperature
display will increase by .5
°
C every half-second.
To decrease the set temperature of the spa water:
Press the OPTIONS hard button on the Main Control panel.
Press the soft button next to
Temperature
.
Press the soft button next to ▼. Each time the button is pressed, the set temperature display will decrease by .5
°
C. If the button is
held down, the set temperature display will decrease by .5
°
C every half-second.
If the set temperature value does not change, check to see whether the TEMP LOCK or SPA LOCK features are on. When either of
these features is activated, the temperature control is disabled.
Summary of Contents for CANTABRIA
Page 1: ...2 0 1 5 O W N E R S M A N U A L 5 0 H z...
Page 75: ......
