Cal Flame BBQ08872U Owner'S Manual Download Page 20

Location of Serial Number Plate

The serial number of your Cal Flame grill is located on 

the back and is visible when the hood is down as shown 

at right.

Grill Specifications

Electrical supply:  220V AC / 50 Hz

Country of destination

BE, CY, CZ, EE, FR, GR, IE, IT, LV, 

LT, LU, PT, RO, SK, ES, CH, BG

AT, HU, SK, CH, DE

Gas category

I3+ (28-30/37)

I3 b/p (50)

Gas and supply pressure

G30 / 28-30/37 MBAR

G30 / 50 MBAR

LTR20081044, Rev. A 

4/21/08

BBQ08872U

2 burner grill

8.78 kWh

BBQ08873U

3 burner grill

16.4 kWh

BBQ08874U

4 burner grill

21.9 kWh

BBQ08874CU

4 burner convection grill

21.9 kWh

BBQ08875U

5 burner grill

28.4 kWh

BBQ08875CU

5 burner convection grill

28.4 kWh

BBQ08852U

Standard single flat side burner

4.4 kWh

BBQ08898U

Deluxe single side burner

4.4 kWh

BBQ08899U

Deluxe double side burner

8.78 kWh

BBQ08953U

Standard side by side burner

8.78 kWh

BBQ08954U

Deluxe double side by side burner

8.78 kWh

BBQ08CR2000U

Two burner cart

8.78 kWh

BBQ08CR3000U

Three burner cart

16.4 kWh

BBQ08CR3000DSU

Three burner cart with double side burner

25.18 kWh

BBQ08CR4000U

Four burner cart

21.9 kWh

BBQ08CR4000DSCU

Four burner convection cart with double side burner 30.68 kWh

BBQ08CR4000CU

Four burner convection cart

21.9 kWh

BBQ08CR5000DSCU

Five burner convection cart with double side burner

37.18 kWh

Summary of Contents for BBQ08872U





















Reviews: