Cadillac Escalade 2020 Owner'S Manual Download Page 128

Page: 128 / 355

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

128

INSTRUMENTS AND CONTROLS

serviced by your dealer. If the system
is working normally, the indicator
light turns off.

If the light stays on and the engine
does not start, there could be a
problem with the theft-deterrent
system. See

Immobilizer Operation

High-Beam On Light

This light comes on when the
high-beam headlamps are in use. See

Headlamp High/Low-Beam Changer

149

IntelliBeam Light

This light comes on when the
IntelliBeam system, if equipped, is
enabled. See

Exterior Lamp Controls

147

Lamps On Reminder

This light comes on when the exterior
lamps are in use, except when only
the Daytime Running Lamps (DRL)
are active. See

Exterior Lamp Controls

147

Cruise Control Light

The cruise control light is white when
the cruise control is on and ready, and
turns green when the cruise control is
set and active.

See

Cruise Control

206

Adaptive Cruise Control Light

This light is white when the Adaptive
Cruise Control (ACC, if equipped) is on
and ready, and turns green when the
ACC is set and active. See

Adaptive

Cruise Control

208

Summary of Contents for Escalade 2020




































































































































































































































































































































































Search results

Summary of Contents for Escalade 2020

Reviews:

Related manuals for Escalade 2020

Brands by name

Popular brands

Cadillac Escalade 2020, Owner'S Manual

Search results

Summary of Contents for Escalade 2020

Reviews:

Related manuals for Escalade 2020

Brands by name

Popular brands