Cadillac CTS 2019 Owner'S Manual Download Page 24 | Manualshive

Page: 24 / 350

background image

Cadillac CTS/CTS-V Owner Manual (GMNA-Localizing-MidEast-12470572) -

2019 - crc - 6/21/18

IN BRIEF

23

avoid or reduce the harm caused by
backing crashes when the vehicle is
shifted into R (Reverse). If the system
detects the vehicle is backing too fast
to avoid a crash with a detected object
behind your vehicle in your path, it
may automatically brake hard to
a stop.

See

Assistance Systems for Parking or

Power Outlets

Power Outlets 12-Volt Direct Current

Accessory power outlets can be used
to plug in electrical equipment, such
as a cell phone or MP3 player.

The vehicle has three 12-volt
accessory power outlets:

.

Inside the center console storage
in front of the armrest cover.

.

Inside the storage area under the
armrest cover.

.

Inside the storage area on the rear
of the center console, if equipped.

These outlets are powered while the
vehicle is on or in ACC/ACCESSORY
mode, or until the driver door is
opened within 10 minutes of turning
off the vehicle.

Lift the cover to access the accessory
power outlet.

See

Power Outlets

.

Sunroof

If equipped, the sunroof will only
operate when the ignition is on or in
ACC/ACCESSORY, or when Retained
Accessory Power (RAP) is active. See

Retained Accessory Power (RAP)

.

The driver side switch (1) operates the
sunroof.

Vent :

Press and release

~

(1) to

vent the sunroof. The sunshade will
automatically open approximately
38 cm (15 in). Press and hold

g

(1)

to close the sunroof vent.

Express-Open/Express-Close :

With

the sunroof in the vent position, press

~

(1) a second time to express-open

the sunroof. Press

g

(1) to

express-close the sunroof. To stop the
sunroof partway, press the switch
again.

The passenger side switch

Q

(2)

operates the sunshade. Press and
release

Q

(2) to express-open or

express-close the sunshade. To stop
the sunshade partway, press the
switch again.

See

.

«
...
22
23
24
25
26
...
»

Summary of Contents for CTS 2019































































































































































































































































































































































Reviews:

No comments

Related manuals for CTS 2019

UNIVERSAL CJ-2A

Brand: Jeep Pages: 27

Brand: Jeep Pages: 228

Brand: Jeep Pages: 108

Brand: Jeep Pages: 525

Brand: Vintage Air Pages: 28

Brand: Pyle Pages: 4

Brand: Whipple Pages: 3

Brand: Whelen Engineering Company Pages: 9

Brand: Sanitas Pages: 36

Brand: Skoda Pages: 2

Brand: Lexus Pages: 830

Brand: Curt Manufacturing Pages: 4

Brand: Whispbar Pages: 112

Brand: Aston Martin Pages: 415

Brand: Renault Pages: 3699

Brand: Reliant Pages: 116

Brand: Tactik Pages: 4

Brand: banks Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands