Cadillac CTS 2019 Owner'S Manual Download Page 192

Page: 192 / 350

Cadillac CTS/CTS-V Owner Manual (GMNA-Localizing-MidEast-12470572) -

2019 - crc - 6/21/18

DRIVING AND OPERATING

191

Auto Engine Stop/Start

When the brakes are applied and the
vehicle is at a complete stop, the
engine may turn off. When stopped,
the tachometer displays AUTO STOP.
See

Tachometer

121

. When the brake

pedal is released or the accelerator
pedal is pressed, the engine will
restart.

To maintain vehicle performance,
other conditions may cause the engine
to automatically restart before the
brake pedal is released.

Auto Stops may not occur and/or Auto
Starts may occur because:

The climate control settings
require the engine to be running
to cool or heat the vehicle interior.

The vehicle battery charge is low.

The vehicle battery has recently
been disconnected.

Minimum vehicle speed has not
been reached since the last
Auto Stop.

The accelerator pedal is pressed.

The engine or transmission is not
at the required operating
temperature.

The outside temperature is not in
the required operating range.

The vehicle is in any gear other
than D (Drive).

Tow/Haul Mode or other driver
modes have been selected.

The vehicle is on a steep hill or
grade.

The driver door has been opened
or the driver seat belt has been
unbuckled.

The hood has been opened.

The Auto Stop has reached the
maximum allowed time.

Auto Stop Disable Switch

If equipped, the automatic engine
Stop/Start feature can be disabled and
enabled by pressing the switch with
the

symbol. Auto Stop is enabled

each time you start the vehicle.

When

is illuminated, the system is

enabled.

Retained Accessory
Power (RAP)

Some vehicle accessories may be used
after the ignition is turned off.

Summary of Contents for CTS 2019































































































































































































































































































































































Search results

Summary of Contents for CTS 2019

Reviews:

Related manuals for CTS 2019

Brands by name

Popular brands

Cadillac CTS 2019, Owner'S Manual

Search results

Summary of Contents for CTS 2019

Reviews:

Related manuals for CTS 2019

Brands by name

Popular brands