Cadence Flash F100-5 User Manual Download Page 29

SPECIFICATIONS

29

F300-2

  Rated Power: 125 Watts RMS @ 4 ohm

  Rated Power: 175 Watts RMS @ 2 ohm

  Bridged Power: 350 Watts @ 4 ohm RMS Mono  /  700 Watts Peak Power

  Minimum THD at Rated Power: < 0.05%

  Frequency Response: 10Hz - 40KHz

  S / N Ratio: > 100dB

  Damping Factor: > 200 @ 100Hz

  Channel Separation: > 65dB

  Dimensions: ( W x H x L ) 11” x 2.75” x 11”

F600-4

  Rated Power: 125 Watts RMS @ 4 ohm

  Rated Power: 175 Watts RMS @ 2 ohm

  Bridged Power: 2 x 350 Watts @ 4 ohm RMS Mono

   1400 Watts Peak Power

  Minimum THD at Rated Power: < 0.05%

  Frequency Response: 10Hz - 40KHz

• 

 S / N Ratio: > 100dB

  Damping Factor: > 200 @ 100Hz

  Channel Separation: > 65dB

  Dimensions: ( W x H x L ) 11” x 2.75” x 18

F100-5

• 

 Rated Power: 100 Watts RMS @ 4 ohm x 4

  Rated Power: 150 Watts RMS @ 2 ohm x 4

  Channel 5: 300 Watts @ 4 ohm RMS Mono

    500 Watts @ 2 ohm RMS Mono
    1800 Watts Peak Power

  Minimum THD at Rated Power: < 0.05%

  Frequency Response: 10Hz - 40KHz

  S / N Ratio: > 100dB

  Damping Factor: > 200 @ 100Hz

• 

 Channel Separation: > 65dB

  Dimensions: ( W x H x L ) 11” x 2.75” x 18” 

F300-3

• 

 Rated Power: 100 Watts RMS @ 4 ohm x 2

  Rated Power: 150 Watts RMS @ 2 ohm x 2

  Channel 3: 300 Watts @ 4 ohm RMS Mono

    500 Watts @ 2 ohm RMS Mono
    1800 Watts Peak Power

  Minimum THD at Rated Power: < 0.05%

  Frequency Response: 10Hz - 40KHz

  S / N Ratio: > 100dB

  Damping Factor: > 200 @ 100Hz

• 

 Channel Separation: > 65dB

  Dimensions: ( W x H x L ) 11” x 2.75” x 18” 

F400-4

  Rated Power: 75 Watts RMS @ 4 ohm

  Rated Power: 125 Watts RMS @ 2 ohm 

    2 x 250 Watts @ 4 ohm RMS Mono  /  1000 Watts Peak Power

  Minimum THD at Rated Power: < 0.05%

  Frequency Response: 10Hz - 40KHz

  S / N Ratio: > 100dB

  Damping Factor: > 200 @ 100Hz

  Channel Separation: > 65dB

  Dimensions: ( W x H x L ) 11” x 2.75” x 13”

F800-4HC

  Rated Power: 125 Watts RMS @ 4 ohm

  Rated Power: 175 Watts RMS @ 2 ohm

  Rated Power: 225 Watts RMS @ 1 ohm

  Bridged Power: 2 x 450 Watts @ 2 ohm RMS Mono

   1800 Watts Peak Power

  Minimum THD at Rated Power: < 0.05%

• 

 Frequency Response: 10Hz - 40KHz

• 

 S / N Ratio: > 100dB

  Damping Factor: > 200 @ 100Hz

  Channel Separation: > 65dB

• 

 Dimensions: ( W x H x L ) 11” x 2.75” x 18”

Summary of Contents for Flash F100-5

































Reviews: