background image

 

 

Button 

Program # (Appears  

in LED window  

when button is pressed) 

For 

Preprogrammed At Factory

to Arby’s Specifications 

 

P1 Turnover 

 

P2 Bacon 

 

P3 

Beef Fast Cook 

 

P4 Bag 

Cheddar 

 

P5 

Left to Operator 

 

 

P6 

Left to Operator 

 

 

P7 – P99 

Optional Additional Operator Presets

(

OR

 to start setting new program) 

 

 

 

Memory button for saving optional 

programs P5 and above  

after programming them 

n/a 

 

3.2 OPERATING NOTES: 

 

Before using the appliance for the first time, be sure to thoroughly clean the inside  of the oven cavity 
(see page 9).

 

Then let the oven run empty for about 30 minutes at a temperature of 350°F to eliminate 

any odors caused by residual protective factory grease. 

 

When the oven is connected to the power supply, the control panel switches on automatically. 

 

When the oven door is opened, heating and fan operation stops automatically. The  built-in fan brake 
is activated. (The fan continues to rotate for a short time only). 

 

Operate the appliance at a room temperature between 41°F to 95°F. 

 

Do not salt food inside the oven cavity. If this is not possible, clean the oven as soon as possible. 

 

When the power is turned on, the light in the cooking cavity will come on and remain on while there 
is power to the oven or when in stand-by mode. The display window will read “

0.00

” (this shows the 

time in hours and minutes). 

 

STAND-BY MODE:

 15 minutes after a preset program ends or the cooking time expires, the light 

inside the cooking chamber will automatically shut off and the oven will go into stand-by mode

 

for 

energy savings.  The display and lights will be off, except for the blue 

 START / STOP light.  

To exit stand-by mode and reactivate the electronic controls, simply press the  

 START / STOP 

button. 
 

 
 
 
 

Summary of Contents for XAFT-115A















Reviews: