10.General Maintenance
11.Cleaning
This appliance does not require scheduled maintenance.
Your Eazi Chef is fitted with a specific size jet (Q) to regulate the correct amount of gas.
Should the hole in the Jet (Q) become blocked, this may result in a small flame or no flame at all. Do not attempt to clean the Jet (Q) with
a pin or other such device as this may damage the orifice, which could make the appliance unsafe.
To replace the Jet (Q):Unscrew the fitting connected to the inlet of the valve (O) before unscrewing the Valve Locknut
Remember that because the valve inlet has a left-hand thread, unscrewing any fitting requires clockwise rotation when viewed from the
fitting end of the valve. The Valve Locknut also unscrews in a clockwise direction.
Remove the Base Plate (E2) by unscrewing the four self tapping screws fixing it to the Tripod housing (E1) and subsequently remove the
Valve (O) from the Housing simply by sliding it out.
The Jet (Q) will now be accessible at the top of the Valve (O).
Unscrew the Jet (Q) from the Valve (O) using a suitable spanner.
Do not use pliers on the jet as this may damage the jet, making it unusable or impossible to remove. Screw the new jet into the valve. Do
not over-tighten as this may damage the jet.
Re-fit the valve and baseplate in the reverse order of assembly. When re-fitting the valve, ensure that the valve spindle aligns with slot in
the Tripod housing.
Reconnect the gas supply as described in the Assembly Instructions
After cooking, leave the burner on low with soapy water in the cooking dish to soften cooking residue. When satisfied that
excess fat has been removed, wash the Skottel BBQ (I1) in warm water using a suitable non-abrasive detergent. Do not use sharp metal
objects or abrasive detergents on the vitreous enamel coated surface.
Remove the fat from the moat at the bottom of the Fat Pan (B) and clean as described for the Skottel BBQ. Wash the Wire Grid
(H1) and Deflector Plate (H2) in warm water with non-abrasive detergent after wiping off any excess fat left after cooking.
: Wash the BBQ Lid (A) in warm water using a suitable non-abrasive detergent. Do not use sharp metal objects or abrasive
detergents, as this will damage the surface coating.
For stubborn stains, oven cleaner may be used.
The Non-stick reversible grill plate is coated with a tough durable non-stick coating that has been used with great success on some of the
best cookware in the world. Nevertheless, taking care of it can help you to enjoy extra years of healthy, easy, non-stick cooking.
Use only low or medium heat settings to help retain the valuable nutrients in the food and maintain the non-stick surface.
Whilst the non-stick coating is very durable, it can easily be damaged by the use of metal cooking utensils. It is therefore recommended
that only plastic or wooden utensils be used when cooking.
Do not overheat the Non-stick reversible grill plate and always add a little cooking oil to the surface before use.
The non-stick coating is perfectly safe in the dishwasher, but the non-stick surface is so easy to clean that a quick hand-wash does the
trick. The use of abrasive detergents is not recommended, as this will permanently damage the non-stick surface.
After cleaning recondition the surface with a light wipe of oil.
Remove the fat from the moat of the Fat Pan (B) and clean as described for the BBQ above.
Replacing a Blocked Jet:
Note: For Parts Reference
Skottel BBQ:
BBQ:
BBQ Lid
Note:
Always allow the Non-stick reversible grill plate to cool before immersing it in water.
Use only low or medium heat settings to help retain the valuable nutrients in the food and maintain the non-stick surface.
Whilst the non-stick coating is very durable, it can easily be damaged by the use of metal cooking utensils. It is therefore recommended
that only plastic or wooden utensils be used when cooking.
Do not overheat the Paella Pan and always add a little cooking oil to the surface before use.
Paella Pan:
Always allow the Paella Pan to cool before immersing it in water.
Care of the Non-Stick Reversible Grill Plate:
The fitting of a hose is described in Section 6 - Assembly of the Appliance.
Replacing the Hose:
(See Fig.2)
Summary of Contents for EAZI CHEF 8200
Page 4: ......