manualshive.com logo in svg

Cabletron Systems SmartSwitch Router, Reference Manual

Share
Download
Cabletron Systems SmartSwitch Router Reference Manual Download Page 186

Chapter 29: SYS Error Messages

29 - 2

SSR-8 Error Reference Manual

Recommended Action:

Upgrade the amount of DRAM DIMM memory to the next highest recommended 
amount.

-SYS-W-HEAP85FULL heap is at 85 percent of maximum usage

Explanation:

System is running low on DRAM.

Recommended Action:

Upgrade the amount of DRAM DIMM memory to the next highest recommended 
amount.

-SYS-W-HEAP95FULL heap is at 95 percent of maximum usage

Explanation:

System is running low on DRAM.

Recommended Action:

Upgrade the amount of DRAM DIMM memory to the next highest recommended 
amount.

-SYS-W-NIAFREETMOUT

network interface not responding to packet free 
requests

Explanation:

Control Module may have a hardware problem.

Recommended Action:

Configure the system to run diagnostics, then reboot.  Note the diagnostics messages.  
If any NIA failures are detected, the Control Modules may be bad and needs replacing.

Summary of Contents for SmartSwitch Router



































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands