Cabletron Systems SmartSwitch Router Reference Manual Download Page 158

Page: 158 / 226

Chapter 23: RCP Error Messages

23 - 4

SSR-8 Error Reference Manual

-RCP-E-CONN RCMD: Connect to address: <address>

Explanation:

This message appears when the SSR could not connect to the rcp server.

Recommended Action:

The rcp server is busy, try again later

-RCP-E-CTRL Error in control packet <string>

Explanation:

This message appears when an internal protocol error occurred.

Recommended Action:

Please try RCP again.

-RCP-E-FILE Could not <string> file <filename>

Explanation:

This message appears when the SSR could not open file on the local file system for
writing

Recommended Action:

Check permissions and file system space available.

-RCP-E-FORMAT <filename> name format error <error_type>

Explanation:

This message appears when a file name contains a colon ':'.

Recommended Action:

Resolution: Check file name and remove colon ':' from the file name

Summary of Contents for SmartSwitch Router



































































































































































































































Search results

Summary of Contents for SmartSwitch Router

Reviews:

Brands by name

Popular brands

Cabletron Systems SmartSwitch Router, Reference Manual

Search results

Summary of Contents for SmartSwitch Router

Reviews:

Brands by name

Popular brands