Cabletron Systems SmartSwitch Router Reference Manual Download Page 182

Page: 182 / 226

Chapter 28: STP Error Messages

28 - 2

SSR-8 Error Reference Manual

created. This could be due to lack of resources. Please call Cabletron Systems technical
support.

-STP-E-FAILREGMGMTADDR failed to register bridge group address

Explanation:

This message appears when bridge group address is not registered.

Recommended Action:

This error is due to an invalid bridge management group address or vlan or port
number.

-STP-E-MCASTREG error registering multicast address - error=<error_code>

Explanation:

This message appears when the bridge group management address could not be
registered.

Recommended Action:

The error could be due to the registration table being full (-51) or the address is not a
multicast address (-55).

-STP-E-NOMEM processing error - insufficient memory

Explanation:

This message appears when memory could not be allocated.

Recommended Action:

This error is due to the unavailability of memory. Please call Cabletron Systems
technical support.

Summary of Contents for SmartSwitch Router



































































































































































































































Search results

Summary of Contents for SmartSwitch Router

Reviews:

Brands by name

Popular brands

Cabletron Systems SmartSwitch Router, Reference Manual

Search results

Summary of Contents for SmartSwitch Router

Reviews:

Brands by name

Popular brands