background image

 

 
 

THE IMPORTANCE OF THE RIGHT APPROACH 

Treasure hunting can be a profitable and rewarding hobby, if approached in a patient and diligent 
manner. Time spent researching to locate a worthwhile site for a search can be time wasted if 
your search is hasty and erratic. To achieve maximum results it is important then, to decide on 
your approach to any particular site in advance of the actual search. 
 
Tactics will be decided by the type of site - it is more profitable to scan a small area thoroughly 
than to conduct a haphazard search of the total site. However, when the site is too far away for 
you to make several return visits, a plan should be adopted which gives maximum coverage, at 
the same time as indicating the most likely area for detailed search. 
 
Your detector alone is not a guarantee of successful treasure hunting. Any detector needs an 
operator and for the best results the operator needs the right approach, attitude and technique. 
Too many beginners neglect the importance of pre-planning and research before using their 
detector in the field, and patience and technique during the actual search. 
 
A successful search should begin with research some time before the day of the actual search. 
The extent and thoroughness of your research will be one of the major factors in the success of 
your detecting. You should aim to get as complete an understanding as possible of the local 
history and geography. 
 
The key to the choice of site is to think of people, where they congregated over the past few 
hundred years. What were their customs and pursuits? Where did they spend money? Where did 
they carry money? The answers are not Roman sites, nor are they associated with mystic treasure 
stories of crocks of gold. Rather, they are unassuming, undramatic places, like public footpaths 
and ancient rights of way, old houses and so on. 
 
When you have chosen your site, allocate a whole day from early morning to early evening for 
the search. Make sure you have all the equipment you are likely to need. Your detector should be 
checked before starting out, and you should always carry a spare set of batteries. You will also 
need a strong, sharp trowel. It is also a good idea to have a set of lines and pins so that you can 
lay out your search area scientifically. 
 
Most beginners make the mistake of rushing about hoping to chance upon a rare find. If for 
example there happened to be a valuable ring that was buried 4" deep on the site you were 
searching, if you rushed about haphazardly and quickly on the site, the odds would be very much 
against you finding it. On the other hand, if you pegged out the area scientifically and searched 
slowly and thoroughly, the odds of finding the ring would be very much more in your favour. 
 
Remember, BE PATIENT and WORK SLOWLY. Do not try to cover too large an area, restrict 
yourself to a small area and work through it thoroughly. Make a note of the position and the 
extent of the area, and then when you return you can start again further on without missing any 
ground or covering the same area twice. 
 
It is also important to keep the detector head as close to the ground as possible. Ideally, you 
should 'iron' the ground with the search head of the detector, so that you do not lose any detection 

 

13

 

Summary of Contents for CS9000 MK2




















Reviews: