C. Davis Systems CDS-LC Operation Manual Download Page 1

C. Davis Systems

CDS-LC

M O D E L   C D S - L C

OPERATIONS MANUAL

TABLE OF CONTENTS

INTRODUCTION

.............................................................................................................................................
1

SECTION 1
1.0

SAFETY.................................................................................................1-1

1.1

EMERGENCY........................................................................................1-1

1.2

Know your machine................................................................................1-1

1.3

Power Supply.........................................................................................1-1

1.4

Keep guards in place.............................................................................1-1

1.5

Wear safety goggles..............................................................................1-1

1.6

Keep Work Area clean...........................................................................1-1

1.7

Avoid Dangerous Environment..............................................................1-1

1.8

Keep Visitors away from work area.......................................................1-1

1.9

Do Not Abuse Cords..............................................................................1-1

1.10 Disconnect Machine...............................................................................1-1
1.11 Remove Tools........................................................................................1-1
1.12 Sharp Objects........................................................................................1-1

SECTION 2
2.0

SYSTEM DESCRIPTION.......................................................................2-1

2.1

Feeder ...................................................................................................2-1

2.2

Crimper...................................................................................................2-2

2.3

Funnel....................................................................................................2-2

2.4

Contact Positioner..................................................................................2-2

SECTION 3
3.0

INSTALLATION.....................................................................................3-1

3.1

Set-Up....................................................................................................3-1

SECTION 4
4.0

SYSTEM OPERATION..........................................................................4-1

4.1

Pre-Start Check List...............................................................................4-1

4.2

Start-Up Procedures..............................................................................4-1

4.3

Operation Description............................................................................4-2

4.4

Operation...............................................................................................4-2

4.5

Shut-Down Procedure............................................................................4-2

4.6

Emergency.............................................................................................4-2

Model #CDS-LC C. Davis Systems Inc., Operations Manual 

Summary of Contents for CDS-LC


















Reviews: