background image

 

 

BroadcastVision Entertainment Technical Support 

Telephone: 1(888) 330-4283 ext.3 

Email: [email protected] 

 

 

 
 

 

Your CAB is enabled for an application as follows:

 

 
 

Proposal Number: 

 

 

Set Top Box: 

 

 

Console Description:        Precor P80 or P82 with Media Adapter 

 

 

If your equipment differs from the information above, please call 

BVE technical support 

at 

1(888)330-4283 ext.3 

for instructions on how to reprogram the CAB onsite. 

 

 
 
 

CAB CONFIGURATION

 

 

There  are  no  special  configuration  requirements  for  CAB  operation  with  your  Precor  console. 
With correct cabling the CAB is  able to  automatically detect the communication signal from the 
console. 

 

The  CAB  ships  pre-configured  by  BVE  for  the  target  STB  at  customer  facility.  Normally  no 
additional configuration steps  are  required. 

If the CAB  does  not  work for  any reason  please 

call  technical  support  at  1(888)330-4283  ext.3  before  leaving  the  facility. 

BVE’s  technical 

support staff is happy to help troubleshoot your problems and get the CAB working properly. 

 

The CAB contains 8 dip-switches internally. Normally these should all be in the OFF position. To 
help  solve  specific  deployment  compatibility  challenges,  BVE  Technical  Support  may  instruct 
that  some  of  the  switch  positions  be  changed 

–  customers  should  not  make  any  changes 

without guidance from BVE support. 

 

 
 

Note: 

The  Broadcastvision  CAB  should  always  be  installed  after  the  cable/satellite  service  has 

already  been  installed,  and  you  have  a  picture  on  the  screen.  If  the  Set  Top  Box  (STB)  is  not 
available at the time of installation you can still run all of the wires and hook up the CAB, but you 
will  not  be  able  to  test  the  CAB  to  make  sure  that  it  is  changing  channels  on  the  STB. 

Summary of Contents for PRECOR P80











Reviews: