background image

- 27 - 

Technical Support

 

 
If you have questions about this product, or if you experience difficulties during the installation, 
contact Butternut at (330) 572-3200.  

 

For best service, please take a few minutes to review this manual before you call. 

 

Another great place for information about the classic Butternut

®

 Antennas is the Butternut

®

 Yahoo 

Group - 

https://groups.yahoo.com/neo/groups/Butternut-antennas/info

 

This special interest group is moderated by Scott Myers, AC8DE and contains a treasure trove of 

Butternut

®

 antenna information from users around the world.

 

 
 
 

Warranty 

 
All products manufactured by Butternut are warranted to be free from defects in material and workmanship 
for a period of one (1) year from date of shipment. Butternut’s sole obligation under these warranties shall be 
to issue credit, repair or replace any item or part thereof which is proved to be other than as warranted; no 
allowance shall be made for any  labor charges of Buyer for replacement of parts, adjustment or repairs, or 
any  other  work,  unless  such  charges  are  authorized  in  advance  by  Butternut.    If  Butternut’s  products  are 
claimed  to  be  defective  in  material  or  workmanship,  Butternut  shall,  upon  prompt  notice  thereof,  issue 
shipping instructions for return to Butternut (transportation-charges prepaid by Buyer). Every such claim for 
breach  of  these  warranties  shall  be  deemed  to  be  waived  by  Buyer  unless  made  in  writing.  The  above 
warranties  shall  not  extend  to  any  products  or  parts  thereof  which  have  been  subjected  to  any  misuse  or 
neglect,  damaged  by  accident,  rendered  defective  by  reason of  improper  installation,  damaged  from  severe 
weather including floods, or abnormal environmental conditions such as prolonged exposure to corrosives or 
power surges, or by the performance of repairs or alterations outside of our plant, and shall not apply to any 
goods  or  parts  thereof  furnished  by  Buyer  or  acquired  from  others  at  Buyer’s  specifications.  In  addition, 
Butternut’s  warranties  do  not  extend  to  other  equipment  and  parts  manufactured  by  others  except  to  the 
extent of the original manufacturer’s warranty to Butternut.  The obligations under the foregoing warranties 
are limited to the precise terms thereof. These warranties provide exclusive remedies, expressly in lieu of all 
other  remedies  including  claims  for  special  or  consequential  damages.  SELLER  NEITHER  MAKES  NOR 
ASSUMES  ANY  OTHER  WARRANTY  WHATSOEVER,  WHETHER  EXPRESS,  STATUTORY,  OR 
IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS, AND NO PERSON 
IS  AUTHORIZED  TO  ASSUME  FOR  BUTTERNUT  ANY  OBLIGATION  OR  LIABILITY  NOT 
STRICTLY IN ACCORDANCE WITH THE FOREGOING. 
 
©Butternut 2016 
 
Butternut

®

, SkyHawk™, SkyLark™ are trademarks of PDS Electronics, Inc. No license to use or reproduce 

any of these trademarks or other trademarks is given or implied. All other brands and product names are the 
trademarks of their respective owners. 
 
Specifications subject to change without notice.             
 
 

Summary of Contents for BUT-HF6V





























Reviews: