Bustec ProDAQ 3411 User Manual Download Page 32

Page: 32 / 40

3411-XX-UM

ProDAQ 3411 24-Ch. ADC Function Card User Manual

Page 32 of 40



1998-2009 Bustec Production Ltd.

A.2 Detailed Register Description

A.1.1 FCID Register
The function card ID register contains a unique number used to identify the card.

Bit

Operation RO RO

RO RO

RO RO RO

Initial

Content

Function Card ID (0xA0D8)

A.1.2 GCSR Register
General control and status register

Bit

Operation RC

-- RWC RW RWC RW RWC WC

Initial

Content

RESET

Resets the function card.

STOP

Writing a one (“1”) to this bit stops the data acquisition. The bit is automatically cleared when

the data acquisition has stopped.

START

Writing a one (“1”) to this bit starts the data acquisition. The bit is automatically cleared when

the data acquisition is finished or has been stopped.

ENA

Enables the data acquisition.

TRG_START

Enables the data acquisition to react on the trigger selected by the ITRI register.

SINGLE

Writing a one (“1”) to this bit will start the data acquisition for one scan only.

FIFO_FF

A one (“1”) indicates that the FIFO memory is full.

FIFO_AF

A one (“1”) indicates that the FIFO memory is almost full (less than 128 words free).

FIFO_HF

A one (“1”) indicates that the FIFO memory is half full.

FIFO_AE

A one (“1”) indicates that the FIFO memory is almost empty (less than 128 words in FIFO).

ADC_TMO

An ADC timeout occured.

REPZERO

A one (“1”) in this bit indicates that the internal repetition counter is zero. This bit is cleared by

reading, but also by starting the data acquisition or reset.

TRIG_I

A one (“1”) indicates that an input trigger as selected by the OTRI register was detected. This

bit is cleared by reading, but also by starting the data acquisition or reset.

FIFO_EM

A one (“1”) indicates that the FIFO memory is empty.

Summary of Contents for ProDAQ 3411




































Search results

Summary of Contents for ProDAQ 3411

Reviews:

Brands by name

Popular brands

Bustec ProDAQ 3411, User Manual

Search results

Summary of Contents for ProDAQ 3411

Reviews:

Brands by name

Popular brands