manualshive.com logo in svg

Bushtec Quantum GL, Owner'S Manual, Page: 21 / 28

Share
Download
Bushtec Quantum GL Owner'S Manual Download Page 21

 

21 

BROWN: 

LEFT TURN SIGNAL 

BLACK: 

INTERIOR LIGHT- SEE SECTION 12 

 
 
14.  SPECIFICATIONS 

 

 

 

 

ROADSTAR  TURBO+2 

QUANTUM   

 

 

 

 

 

 

 

          SPORT & “GL” 

BASE WEIGHT(LBS)* 

 

125 

 

125 

 

150 

 

 

CARGO AREA DIMENSIONS(inches)** 
Height   

 

 

 

 18 

 

 16 

 

 16 

 

 

 

Length   

 

 

 

 38.5   

 43 

 

 45 

 

 

Width   

 

 

 

 23 

 

 23 

 

 23 

 

 

MAXIMUM CARGO DIMENSIONS(inches)*** 
Height   

 

 

 

 24 

 

 23 

 

 24 

 

 

Length   

 

 

 

 52 

 

 54 

 

 54 

 

 

 

Width   

 

 

 

 40 

 

 38 

 

 38 

 

 

 

VOLUME(Cubic Feet) 

 

 21 

 

 25 

 

 26 

 

 

 

OVERALL LENGTH  (inches) 

 87 

 

 87 

 

 89 

 

 

LOAD CAPACITY(GVWR)    

350 

 

350 

 

350 

 

 

(LBS.) 
 
*-Approximate Weight 
**-Dimensions at narrowest interior points. 
***-Dimensions at widest exterior points. 
 
NOTE:  Specifications are subject to change at any time without prior notice. 
 

15.  CERTIFICATION LABEL LOCATION 

Every Bushtec trailer is assigned its own unique WMI compliant VIN number which is 
located on a Certification label on the trailer chassis.  The VIN tag is located on the 
chassis neck under the nose of the body and can be viewed from the left side of the 
trailer.  Besides containing the year, make, model, and VIN number, it also contains 
information on axle weight rating, gross vehicle weight rating, rim size, and tire size and 
pressure information, it indicates that the trailer meets all DOT requirements. 
 

 
 

Summary of Contents for Quantum GL





























Reviews:

No comments