background image

SAFETY

XLRR-I   05/21

Safety Section 1-5

© 2021 Alamo Group Inc.

SA

FE

TY

Use  extreme  care  when  lowering  or  unfolding  the  implement’s  wings.      Make  sure  no

bystanders  are    close  by  or  underneath  the  wings.   Allow  ample  clearance  around  the

implement when folding or unfolding the wings.  Use extreme caution around buildings or

overhead power lines.  

(S3PT-05)

There are obvious and hidden potential hazards in the operation of this implement as in all

power-driven or pulled equipment. REMEMBER! This machine is often operated in rough

terrain conditions that include tall grass, weeds, gullies, holes, slopes, hidden obstructions

and the like. Serious injury or even death may occur unless care is taken to assure the

safety of the operator and bystanders in the area. Do not operate this machine with anyone

in the immediate area  

 (S3PT-07)

This Implement may be wider than the Tractor.   Be careful when operating or transporting

this equipment to prevent the Implement from running into or striking sign posts, guard rails,

concrete abutments or other solid objects.  Such an impact could cause the Implement and

Tractor to pivot violently resulting in loss of steering control, serious injury, or even death.

Never allow the Implement to contact obstacles. 

 (S3PT-12)

Operate this Implement only in conditions where you have clear visibility in daylight or with

adequate artificial lighting. Never operate in darkness or foggy conditions where you cannot

clearly see at least 100 yards in front and to the sides of the tractor and implement. Make

sure  that  you  can  clearly  see  and  identify  passersby,  steep  slopes,  ditches,  drop-offs,

overhead obstructions, power lines, debris and foreign objects. If you are unable to clearly

see these types of items discontinue operating this equipment.

(S3PT-21)

Operate  this  Equipment  only  with  a Tractor  equipped  with  an  approved  roll-

over-protective system (ROPS). Always wear seat belts. Serious injury or even

death could result from falling off the tractor, particularly during a turnover when

the operator could be pinned under the ROPS.  

(SG-7)

BEFORE leaving the tractor seat, lower the implement, set the parking

brake and/or set the tractor transmission in parking gear, disengage the

PTO, stop the engine, remove the key, and wait for all moving parts to

stop.  Place  the  tractor  shift  lever  into  a  low  range  or  parking  gear  to

prevent the tractor from rolling. Never dismount a Tractor that is moving

or  while  the  engine  is  running.  Operate  the  Tractor  controls  from  the

tractor seat only.

  (SG-9)

Never allow children or other persons to ride on the Tractor or Implement.

Falling off can result in serious injury or death.  

(SG-10)

Summary of Contents for XLRR1022-I



















































































Reviews: