![background image](http://html1.mh-extra.com/html/bush-hog/sm-60/sm-60_operators-manual_2834708011.webp)
F. Pull driveline apart. Attach the outer (female)
section to the tractor PTO shaft and the inner (male)
section to the pump input shaft. Pull on each drive-
line section to make sure yokes lock into place.
G. Hold driveline sections parallel to each other to
determine if driveline is too long. (Fig. 2-4) If drive-
line must be shortened, perform steps “D”
through “H” in paragraph 2-2.
H. Position implement at point with greatest dis-
tance between pump input shaft and PTO shaft.
I. Hold driveline halves parallel to each other
and check for minimum of 6 inches (15 cm) over-
lap. (Fig. 2-1)
J. Apply multi-purpose grease to inside of outer
(female) driveline section. Assemble driveline and
install on machine and implement. Pull on each driv-
eline section to make sure yokes lock into place.
K. Raise implement off ground. Pin parking stand
in the up position. (Fig. 2-2)
Figure 2-2 Parking Stand In Up Position
L. Remove transport lock pin located at deck pivot
linkage and insert into storage holes. (Fig. 2-3)
STAY CLEAR OF DECK DURING AND AFTER
REMOVAL OF LOCK PIN. AIR IN HYDRAULIC
LINES COULD ALLOW CUTTER DECK TO
FALL, CAUSING POSSIBLE INJURY.
M. Position cutter deck straight out (parallel to
ground) and approximately 2 inches (51 mm) from
ground.
N. Adjust cutter deck front to rear using top link of
3-point hitch. Rear of cutter deck should be 1-2
inches (25-51 mm) higher than front.
O. Adjust lower 3-point hitch arms to level cutter
deck sliding beam right to left.
P. Adjust 3-point hitch position control to stop at
present height. This will prevent accidental dragging
of sliding beam.
WARNING
Fig. 2-3 Pivot Linkage
Q. If equipped with optional valve stand, adjust to
desired working position.
R. Raise cutter deck and install transport lock pin
before traveling. (Fig. 2-3)
NOTE
It is recommended that front end ballast
(weights) be added to tractor for stabilization. In
some uses, added stabilization may be gained
by weighting left rear wheel heavier than right
rear wheel. Do not exceed tractor ballast rating.
Consult your tractor dealer.
2-2 DRIVELINE MODIFICATION
IMPORTANT
IT IS EXTREMELY IMPORTANT THAT DRIVELINE
MATCH THE TRACTOR BEING USED. IF UNIT IS
ATTACHED ON ANOTHER TRACTOR, DRIVELINE
MUST BE CHECKED FOR CORRECT LENGTH.
FAILURE TO MATCH DRIVELINE TO TRACTOR
WILL CAUSE FAILURE TO THE PUMP.
Due to the many variations in tractor/implement
hitch points and corresponding differences in dis-
tances between tractor PTO shafts and implement
input shafts, drivelines may need to be shortened as
follows:
A. Attach implement to tractor 3-point hitch.
B. Raise and lower implement to determine the
shortest distance between the tractor PTO shaft and
the pump input shaft. Stop tractor leaving imple-
ment in position of shortest distance. Block imple-
ment in position.
C. Pull driveline apart. Attach the outer (female)
section to the tractor PTO shaft and the inner (male)
section to the pump input shaft. Pull on each drive-
line section to make sure yokes lock into place.
D. Hold driveline halves parallel to each other to
determine amount to be removed. Measure approxi-
mately 3 in. (76 mm) back from the opposite univer-
sal joint shield and mark the free end of the shield.
Do this for each section. (Fig. 2-4)
E. Clamp the end of driveline in a vice. Cut off
shield at point it was marked.
F. Using the cut off section of shield as a guide,
cut the shaft the same amount. (Fig. 2-6)
8
Overlap Minimum
Figure 2-1
Pin Storage Hole
Transport Lock Pin
All manuals and user guides at all-guides.com
all-guides.com