i
mportant
safety
information
for
operating
the
f
alz
C
utter
•
Before setting up the tool always make sure to remove the
accumulator from the cordless drill!
•
When performing operation that’s not associated with the
seaming task the cordless drill must be removed from the
cordless drill!
•
Carefully read all safety information before operating the FALZ CUTTER and save it
for future reference.
•
As a matter of principle, any person who is put in charge with the start-up, oper-
ation, maintenance and repair of the machine must have read and understood
the operating instructions, specifically the chapter on safety.
•
When working with FALZ CUTTER on a roof, always use roof lifeline and follow all
safety regulations
•
Before using FALZ CUTTER for the first time, carefully remove all packing materials.
•
Always make sure that FALZ CUTTER is properly assembled before using.
•
During the work hold hands, fingers, hair, clothes and other tools at a safe dis
-
tance. Never place your hands, fingers or tools between the discs.
•
Do not overreach. Keep proper footing and balance at all times.
•
Stay alert. Watch what you are doing. Use common sense. Do not operate tool
when you are tired or under the influence of drugs, alcohol or medication. A mo
-
ment of inattention while operating may result in serious personal injury.
•
Do not wear loose clothing or jewellery. Keep your hair, clothing, and gloves away
from moving parts. Loose clothes, jewellery or long hair can be caught in moving
parts.
•
After using FALZ CUTTER , make sure that the tool isn’t wet and then placed in the
box. If sand and dust accumulate around the discs, clean them.
•
Do not expose the FALZ CUTTER to extreme temperatures, it is not recommended
to operate the device in cold weather (below zero degrees). Do not expose FALZ
CUTTER to rain or use them under moist or wet condition.
•
This tool is not intended for use by children. Ensure that children do not have
access to the FALZ CUTTER.
•
When FALZ CUTTER and accesories are not in use, keep them in a safe place.
•
It is strictly forbidden to put and keep a wet FALZ CUTTER in a case.
o
perating
instruCtion
of
f
alz
C
utter
•
The FALZ CUTTER is to be operated exclusively by qualified and authorised persons
who must know the national accident-prevention rules.
•
Obligated to check the FALZ CUTTER for externally visible damage and defects
before starting work and to notify and eliminate any changes (including the oper-
ation behavior) that affect the safety.
•
Sight-checking all screws - tighten screws if necessary.
•
Position the Falz Cutter with the cordless drill machine
•
Check if the roof dimensions of profile are within the maximum allowable dimen
-
sions, see “Correct usage” page.
•
In order for Falz Cutter to work properly Cordless drill speed must be set at 1
( 500-550 RPM )
•
If a profile is needed to be cut by full lenght then cutting discs must be placed at
the beginning of the metal roof ( each cutting disc must on different side ) And
start the cutting process. ( Make sure that the profile side is on the left side )
•
If it’s necessary to start the cutting process from the middle of the profile then
place the Falz Cutter on the profile ( each cutting disc must be on different side
) Tilt the cordless drill machine by 20 - 30 degrees and start the cutting process.
Tilting the cordless drill machine by 20 - 30 degrees to the opposite side the Falz
Cutter can be deatached. ( For this option we recommend powerfull cordless drill
machine ) 110+ NM
•
The Cordless drill works clockwise and Falz Cutter is operating in forwards direc-
tion
! DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to safety rules for the subject
product. MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. !
