manualshive.com logo in svg

BUSCH PANDA WZ 2400 A, Instruction Manual, Page: 12 / 28

Share
Download
BUSCH PANDA WZ 2400 A Instruction Manual Download Page 12

5 | Installation

12 / 28

0870203784_WZ2400A_-0001_IM_en

1

4

3

MAX

MIN

2

Busch Oil

Check oil level

Oil filling at the gear side

When the oil filling is achieved:

• Write down the oil change date on the sticker.

Last oil change

__ / __ / ____

Oil type see nameplate

Change interval see 

instruction manual

If there is no sticker (part no. 0565 568 959) on the machine:

• Order it from your Busch representative.

5.4 Electrical Connection

DANGER

Live wires.

Risk of electrical shock.

• Electrical installation work must only be executed by qualified personnel.

• Make sure that the power supply for the motor is compatible with the data on the

nameplate of the motor.

• The electrical installation must comply with applicable national and international

standards.

• Provide a lockable disconnect switch on the power line so that the machine is com-

pletely secured during maintenance tasks.

• Provide an overload protection according to EN 60204-1 for the motor.

Summary of Contents for PANDA WZ 2400 A





























Reviews:

No comments