background image

5 | Storage

6 / 20

Installation and Retrofit Instructions DOLPHIN LM 0180-0270 A, LT 0170-0220

A_EN_en

5

Storage

NOTICE

Long storage time.

Risk of damage to the variable-frequency drive!

Due to a long storage time the capacitors of the variable-frequency drive can lose effi-
ciency because of electrochemical processes. In worst case it can lead to a short circuit
and therefore to a damage to the variable-frequency drive.

• Connect the variable-frequency drive every 2 years for 30 minutes to the mains.

• Store the motor with the variable-frequency drive indoor, dry, dust free and if possible

in the original packaging preferably at temperature between -20 … 60 °C.

6

Installation

DANGER

Carry out any work on the variable-frequency drive and motor.

Risk of electrical shock!

• Electrical installation work must only be executed by qualified personnel.

DANGER

The installation conditions are not respected.

Risk of electrical shock!
Risk of severe injury!

• Take care that the installation conditions are met.

CAUTION

The machine can start immediately when power is supplied.

Risk of inadvertent start-up!

• Make sure that a start-up will not lead to a dangerous situation.

6.1 Installation Conditions

• Make sure that the variable-frequency drive is de-energised.

• Make sure that the variable-frequency drive is grounded in accordance with DIN EN

61140; VDE 0140, NEC and other relevant standards.

• Make sure that unused open cable ends in the motor terminal box are insulated.

• Make sure that mains connections are hardwired.

• Make sure to use suitable line circuit breakers with the prescribed nominal current be-

tween the mains and the variable-frequency drive, see 

Line Protection [

 7]

.

• Make sure that the ambient conditions are complied with, see 

Ambient Conditions

[

 7]

.

Summary of Contents for LM 0180 A





















Reviews: