background image

Table of Contents

2 | 48

Instruction Manual COBRA NC 0100-0300 B ACV_EN_en

Table of Contents

1

Safety.....................................................................................................................................................................

4

2

Product Description.............................................................................................................................................

5

2.1

Operating Principle .............................................................................................................................................

6

2.2

Intended Use .......................................................................................................................................................

6

2.3

Start Controls.......................................................................................................................................................

7

2.4

Standard Features...............................................................................................................................................

7

2.4.1

Air Cooling .............................................................................................................................................

7

2.4.2

Temperature Switch .............................................................................................................................

7

2.4.3

Sealing Systems.....................................................................................................................................

7

2.5

Optional Accessories...........................................................................................................................................

7

2.5.1

Gas Ballast Valve ...................................................................................................................................

7

2.5.2

Silencer...................................................................................................................................................

7

2.5.3

Barrier Gas System ...............................................................................................................................

7

2.5.4

Mechanical Seals...................................................................................................................................

7

2.5.5

Nitrogen Panel ......................................................................................................................................

8

2.5.6

Pressure Switch (Barrier Gas)..............................................................................................................

8

3

Transport ..............................................................................................................................................................

9

4

Storage ..................................................................................................................................................................

10

5

Installation ...........................................................................................................................................................

11

5.1

Installation Conditions........................................................................................................................................

11

5.2

Connecting Lines / Pipes ....................................................................................................................................

12

5.2.1

Suction Connection............................................................................................................................... 12

5.2.2

Discharge Connection .......................................................................................................................... 13

5.2.3

Barrier Gas System Connection (Optional) ........................................................................................ 13

5.2.4

Dilution Gas System Connection (Optional) ...................................................................................... 14

5.2.5

Purge Gas System Connection (Optional).......................................................................................... 15

5.3

Filling Oil...............................................................................................................................................................

16

5.4

Filling Cooling Liquid...........................................................................................................................................

18

5.5

Liquid Flushing Device Installation (Optional).................................................................................................

18

5.6

Fitting the Coupling ............................................................................................................................................

19

6

Electrical Connection...........................................................................................................................................

21

6.1

Machine delivered without Variable Speed Drive ...........................................................................................

21

6.2

Machine delivered with a Variable Speed Drive (Option)...............................................................................

22

6.3

Wiring Diagram Three-Phase Motor (Pump Drive).........................................................................................

23

6.4

Wiring Diagram Solenoid Valve (Optional).......................................................................................................

24

6.5

Electrical Connection of the Monitoring Devices ............................................................................................

25

6.5.1

Wiring Diagram Temperature Switch................................................................................................. 25

6.5.2

Wiring Diagram Flow Switch (Optional) ............................................................................................. 25

6.5.3

Wiring Diagram Pressure Switch (Optional)...................................................................................... 25

6.5.4

Wiring Diagram Level Switch (Optional) ............................................................................................ 25

7

Commissioning.....................................................................................................................................................

26

7.1

Conveying Condensable Vapors........................................................................................................................

27

7.2

Liquid Flushing Procedure .................................................................................................................................

27

7.3

Gas Purging Procedure ......................................................................................................................................

27

8

Maintenance.........................................................................................................................................................

28

8.1

Maintenance Schedule .......................................................................................................................................

29

8.2

Oil Level Inspection.............................................................................................................................................

30

8.3

Cooling Liquid Level Inspection.........................................................................................................................

30

Summary of Contents for COBRA NC 0100 B

















































Reviews: