BUSCH COBRA NC 0100 B Instruction Manual Download Page 15

Page: 15 / 48

Installation | 5

Instruction Manual COBRA NC 0100-0300 B ACV_EN_en

15 | 48

●

Connect the dilution gas connection (DGC) to the gas supply.

Connection size:
– G1/4, ISO 228-1

●

Electrically connect the solenoid valve (MV), see Wiring Diagram Solenoid Valve [

➔

24].

●

Make sure that the gas complies with the following requirements:

Gas type

Dry nitrogen

Gas temperature

°C

0 ... 60

Maximum gas pressure

bar

Recommended pressure setting at the pres-
sure regulating valve (PRV)

bar

0.5

Filtration

µm

Recommended flow rate

SLM (standard li-
ter per minute)

5.2.5

Purge Gas System Connection (Optional)

PRV

PGC

MAN

FME, FR

NIP

INF

Description

PGC

Purge gas connection

FME

Flow meter

Flow regulator

INF

Inlet flange

MAN

Manometer

Solenoid valve

NIP

Nitrogen panel

PRV

Pressure regulating valve

●

Connect the purge gas connection to the gas supply.

Connection size:
– G1/4, ISO 228-1

Summary of Contents for COBRA NC 0100 B

















































Search results

Summary of Contents for COBRA NC 0100 B

Reviews:

Related manuals for COBRA NC 0100 B

Brands by name

Popular brands

BUSCH COBRA NC 0100 B, Instruction Manual

Search results

Summary of Contents for COBRA NC 0100 B

Reviews:

Related manuals for COBRA NC 0100 B

Brands by name

Popular brands