–
Approximate flow rate: 6 - 7 l/ min for the standard version (hot
pump)
–
Approximate flow rate: 6 - 15 l/ min for other applications
l
Make sure that the cooling water is neutral and clean
l
Make sure that the cooling water outlet is unpressurised
l
Make sure that the nitrogen fulfills the following requirements:
–
Overpressure: 1,5 bar
–
Approximate flow rate: 0 - 75 l/ min
l
Make sure that the ambient conditions correspond to the protec-
tion class of the motor (according to nameplate)
l
Make sure that the vacuum pump is placed on or fastened to a
horizontal surface
l
Make sure that the vacuum pump is level
l
Make sure that the vacuum pump is at least 1 m away from any
wall to ensure good cooling
l
Make sure that the vacuum pump is easily accessible and that the
selected installation site fulfills the requirements for assembly/ dis-
mantling
l
Make sure that no temperature-sensitive parts (for example, of
plastic, wood, cardboard, paper, electronic parts) come into con-
tact with the hot surfaces of the vacuum pump
l
Make sure that the installation site or assembly area is ventilated in
such a way that adequate cooling of the vacuum pump is ensured
CAUTION
The surface temperature of the vacuum pump can exceed 50°C
when the vacuum pump is in operation.
Danger of burns!
l
Make sure that no-one can touch the vacuum pump accidentally.
If necessary, attach safeguard
l
Make sure that the oil sight glasses (OSG) are easily accessible
If oil changes are to be made on site:
u
Make sure that the oil drain and oil filler are easily accessible
Inlet connection
l
Make sure that the protection that was attached to prevent pene-
tration of particles during transport has been removed before the
vacuum pump is connected to the vacuum line
CAUTION
Do not put hands into the inlet aperture.
Risk of body damage!
CAUTION
The intake of liquids or solid particles can lead to the destruction of
the vacuum pump
If the sucked gas contains dusts or solid foreign bodies:
u
Make sure that a filter or protective grating is installed at the
extraction point
l
Make sure that the nominal diameter of the intake line is at least
equal to the diameter of the intake flange of the vacuum pump to
prevent a drop in the performance of the vacuum pump in the case
of a smaller cross-section
l
Make sure that the vacuum pump is connected with leakproof lines
CAUTION
When the intake lines have been connected, make sure that the
system does not leak. Leakages of dangerous substances must be
prevented!
l
Make sure that the intake lines are equipped with a shut-off device
upstream of the intake flange so that the flow of sucked gas can
be stopped
l
Make sure that the intake lines do not exercise any force on the in-
take flange. Mount bellows if necessary.
l
The inlet flange has the following dimension:
DS 0080 G
DN 40 ISO KF
DS 0160 G
DN 50 ISO KF
DS 0700 G
DN 63 ISO K
DS 1000 G
DN 100 ISO K
DS 2000 G
DN 160 ISO K
In the case of long intake lines, the line cross-section should be larger
than the intake flange to prevent a drop in the performance of the
vacuum pump. If you have any doubts, contact your Busch
representative.
Discharge connection
The following instructions for connection to the discharge only apply if
the sucked gas is discharged by the vacuum pump into a suitable
environment.
l
Make sure that the protection that was attached to prevent pene-
tration of particles during transport has been removed before the
vacuum pump is connected to the vacuum line
l
Make sure that the nominal diameter of the exhaust line is at least
equal to the diameter of the exhaust flange of the vacuum pump
to prevent a drop in the performance of the vacuum pump in the
case of a smaller cross-section
l
Make sure that the vacuum pump is connected with leakproof lines
CAUTION
Do not put hands into the outlet aperture.
Risk of body damage!
CAUTION
When the discharge lines have been connected, make sure that the
system does not leak. Leakages of dangerous substances must be
prevented!
l
Make sure that the discharge line is mounted in such a way that
condensate cannot penetrate into the pump (siphon trap, gradient)
l
Make sure that no shut-off devices are mounted in the discharge
line
l
Make sure that the discharge lines do not exercise any force on the
discharge flange. Mount bellows if necessary
l
The discharge flange has the following dimension:
–
DN 40 ISO KF
In the case of long discharge lines the line cross-section should be
larger than the discharge flange to prevent a drop in the performance
of the vacuum pump. If you have any doubts, contact your Busch
representative.
DS 0080-2000 G
Installation and start-up
0870772712 (En)
Page 13
