background image

   EF675

 User’s Manual   

9

English

1. Wait until the  

SLIP

 light blinks. Then insert the check 

face up

 

with the right side of the check against the right side of the 
paper inlet as far as it will go. Be sure that the MICR characters 
are on the right. 

2. The printer will detect the check and start drawing it in. When 

the printer starts drawing it in, let go of the check immediately. 
When the printer ejects the check and the 

SLIP

 light starts 

blinking again; remove the check by pulling it straight up; do 
not pull it at an angle.

Cleaning the MICR Mechanism

Once a year clean the MICR head with a moistened cleaning sheet. 

Use the following or an equivalent commercially available cleaning 
sheet: PRESAT brand (KIC) “CHECK READER CLEANING CARD.”

          To order call 1-800-448-1424 

                Note:
                

Be sure not to use an adhesive cleaning sheet.

                Follow the steps below:

                1. Load a paper roll in the printer; turn off the power; then open 

               the paper roll cover and turn the power back on while holding 
               down the RELEASE button.

                  2. Press the RELEASE button seven times; then close the paper roll 

               cover. The printer prints the following message on receipt 
               paper and the SLIP light flashes.

MICR 
characters 
on this side 
face up

 

675u_6.book  Page 9  Thursday, November 27, 2003  10:22 AM

Summary of Contents for EF675



















Reviews: