background image

6

User Maintenance

A.

  General Housekeeping (Continuous).

1.  Keep boiler area clear and free of combustible 

materials and obstructions to the free flow of 

combustion and ventilation air to the boiler.

2.  Do not store or use gasoline or other flammable 

vapors or liquids in the vicinity of the boiler or any 

other appliance.

3.  Do not store or use sources of hydrocarbons in 

the vicinity of the boiler. Sources of hydrocarbons 

include bleaches, cleaners, chemicals, sprays, paint 

removers, fabric softeners and refrigerants.

B.

  Inspect Concentric Inlet Air/Vent System (Monthly).

1.  Concentric Inlet Air/Vent Terminal must be free 

of obstruction and undamaged due to impact or 

excessive temperature.

2.  Concentric Inlet Air/Vent Terminal exterior wall 

penetration must be weather tight.

3.  Concentric Inlet Air/Vent pipe must be supported at 

maximum 5 ft interval and must not sag.

Figure 3: Burner Flame

4.  All Concentric external Inlet Air pipe joints must be 

secure and airtight.

5.  All Concentric internal Vent pipe joints must be 

secure, gas tight and watertight.

6.  Condensate drain must be free of obstruction and 

allow condensate to flow freely.  If corrective action 

is required, contact your installer or qualified service 

agency.

C.

  Inspect burner Flames (Monthly).

1.  Remove lower front door assembly.

2.  Adjust thermostat to the highest setting to initiate 

boiler firing.

3.  View burner flames through observation glass.
4.  Check burner flames.  See Figure 3.  On high fire 

the flame should be stable and mostly blue.  No 

true yellow tipping should be present, however 

intermittent flecks of yellow and orange in the 

flame, caused by dust in air, are normal.

WARNING

Service on this boiler should be undertaken only by trained and skilled personnel from a qualified service 

agency.  Inspections  should  be  performed  at  intervals  specified  in  Installation,  Operating  and  Service 

Instructions and this manual. Maintain manuals in a legible condition.
Keep boiler area clear and free of combustible materials, gasoline and other flammable vapors and liquids.
Do not place any obstructions in boiler room that will hinder flow of combustion and ventilation air.

Summary of Contents for Alpine Series









Reviews: