manualshive.com logo in svg

Burlington SP697, Installation Instruction, Page: 5 / 7

Share
Download
Burlington SP697 Installation Instruction Download Page 5

F

 "Y" scale

 Exposed
 "X" steps

2

0

5 - 7

Note:

The above diagram is for reference only. In this example, X is set to 17 and Y is set to 3.

The inlet valve can be adjusted to suit the particular cistern, please refer to below tables for
the settings.

For adjustment method, please refer to the installation instruction on 

page 1 & 2

.

Inlet Valve Adjustment Instructions

For 6L full flush and 3L half flush

Cistern code

            

X

             

 Y

CC.1036

               17

         3

CM0007

                20

         3

15.B.27353

           19

         2

15.B.27349

           17

         2

SPH002

                21

         1

MAR.006

               21

         0

For 4.5L full flush and 2.6L half flush

Cistern code

            

X

             

 Y

CC.1036

              

13

          3

CM0007

               

17

          3

15.B.27353

          

14

          2

15.B.27349

          

16

          2

SPH002

               

19

          1

MAR.006

              

19

          0

Summary of Contents for SP697








Reviews:

No comments